EINHELL RT-TC 620 U Originalbetriebsanleitung Seite 20

Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect condi-
tion.
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
•
Wear gloves.
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The fol-
lowing hazards may arise in connection with
the equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is applied.
3. Health damage caused by hand-arm vibra-
tions if the equipment is used over a longer
period or is not properly guided and maintai-
ned.
6. Before starting the equipment
•
The machine must be set up so that it stands
firmly, i.e. it must be securely screwed to a
work bench, to the base frame supplied, or
similar.
•
All covers and safety devices have to be pro-
perly fitted before the equipment is switched
on.
•
The cutting wheel must rotate smoothly.
•
Check that the voltage on the rating plate is
the same as your supply voltage before you
connect the equipment to the power supply.
7. RCD plug
1. Connect the RCD plug to the power supply.
2. Press the Reset button.
3. The indicator lamp will begin to shine.
4. Press the Test button to check the function of
the RCD plug.
5. If everything is working properly the indicator
lamp will go out and contact to the power sup-
ply will be interrupted (the RCD plug triggers
at a fault current of 10mA). If the RCD plug is
defective, the indicator lamp will continue to
Anleitung_RT-TC_620U.indd 20 Anleitung_RT-TC_620U.indd 20
GB
shine.
6. Press the Reset button again to switch on the
machine.
Note:
If the RCD plug is defective, it must be replaced
by a qualifi ed electrician.
8. Assembly and operation
8.1 Unfolding the base frame (Fig. 2)
•
To set up the equipment on its feet (1), press
the latching button (a) and lower the respec-
tive feet (1) until they latch in the intended
position. To fold up the feet (1), proceed in
reverse order.
8.2 Fitting the cooling water pump (Fig. 4 - 6)
•
First place the container (a) for the cooling
water pump (13) in the intended position on
the trough (3).
•
Place the cooling water pump (13) - with the
suction cups pointing down - into the contai-
ner (a).
•
Then fasten the hose to the intended posi-
tions as shown in Fig. 5 and 6.
Important!
To guarantee proper operation, the cooling water
hose (14) must not be kinked during installation.
Caution!
It must be impossible for the cable and the coo-
ling water hose to get into the cutting area.
8.3 Fitting the transport aids (Fig. 7 - 9)
•
Fit the transport wheels (19), the parking foot
(20) and the transport handle (18) as shown
in Figs. 7/8/9.
8.4 Fitting the stop rail and the angle stop
(Fig. 10)
•
First push the stop rail (6) onto the guides (a)
as shown and fasten.
•
Then you can push the angle stop (5) into the
guide (b) and fasten in any position.
8.5 On/Off switch (Fig. 3/4)
•
To switch on, press the „1" on the On/Off
switch (16).
•
Before you begin cutting, wait until the cutting
wheel has reached maximum speed and the
cooling water pump (13) has started supply-
- 20 -
04.11.11 08:12 04.11.11 08:12