Music Control; Foot Remote Control; Master / Slave Mode; Dmx Control - IMG STAGE LINE PARL-45SET Bedienungsanleitung

4) To save the setting, press the button ENTER
repeatedly until
appear on the display.

5.1.3 Music control

The spotlights can be music-controlled by means of
the microphone (7). Four different control programs
are available:
1) Press the button MENU repeatedly until
appears on the display.
2) Press the button ENTER: The music mode most
recently set will be activated and indicated on
the display. Use the button
of the following modes:
= colour change red, green, blue, yellow,
turquoise, purple, white, red ...
= colour change red, green, blue, red ...
= running light
= white flashes only
3) To save the setting, press the button ENTER so
that appears on the display.
4) Turn the control SENSITIVITY (6) for the sensi-
tivity of the microphone (7) clockwise until the
spotlights respond to the music as desired.
When the volume of the music system is
changed, the sensitivity of the microphone must
be adjusted accordingly. If the music control
does not operate in an optimal way even though
the sensitivity control has been set to a high
level, increase the volume or reduce the dis-
tance between the sound source and the micro-
phone.

5.1.4 Foot remote control

Use the foot remote control (13) supplied to select
the 12 light programs and 7 different lighting
colours.
1) Connect the plug of the remote control to the
jack (10) of the controller. Tighten the lock nut to
secure the connection.
2) Press the foot switch PROGRAMS to select the
7 lighting colours one after the other at maxi-
mum brightness.
play.
3) Press the foot switch PROGRAMS again to
select the 12 light programs one after the other
( ... will appear on the display). Then
will appear on the display and the programs
will change automatically. To restart the selec-
tion cycle with
GRAMS again.
4) Press the foot switch BLACKOUT to switch off
the light ( will appear on the display). To
and the program number
or to select one
will appear on the dis-
, press the foot switch PRO-
switch on the light again, press the foot switch
BLACKOUT again, or, to go to the next light pro-
gram, press the foot switch PROGRAMS.

5.1.5 Master / slave mode

Multiple units PARL-45SET can be operated in
sync. In this mode, one unit (master unit) controls
the other units. Connect the units with each other
in a chain; please refer to chapter 5.2.1, skipping
step 1.
1) Set all slave units to the slave mode:
a) Press the button MENU repeatedly until
and a number between 001 and 512 appear
on the display.
b) Press the button ENTER so that a dot lights
up on the right of .
c) Use the button
001.
d) Press the button ENTER to save the setting.
The dot will extinguish. When the slave unit
receives control signals from the master unit,
the dot will flash rapidly.
2) At the master unit, set the desired operating
mode ( chapters 5.1.1 – 5.1.3).
3) To control all slave units in sync by means of the
master unit, connect the foot remote control to
the master unit (

5.2 DMX control

DMX (Digital Multiplex) allows for digital control of
multiple DMX units by means of a common control
line. For operation via a DMX light controller, the
spotlight set is equipped with 15 DMX control chan-
nels. However, it can also be controlled by 3 chan-
nels only, if required. The functions of the channels
and the corresponding DMX values for the 15-
channel mode can be found in chapter 6.1.
The following units from IMG STAGELINE are
suitable for DMX operation of the PARL-45SET:
Number of
Model
DMX channels
DMX-1USB 510
DMX-510USB 510
DMX-3216 512
DMX-4840 484
LC-8LED 128
or to set the number to
chapter 5.1.4).
Remark
computer software
with DMX converter
computer software
with DMX converter
DMX controller
DMX controller
controllable in
the "Record" mode
13