DeWalt DCD791 Bersetzung Der Originalanweisungen Seite 22

EnGLIsH
6) Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
b ) Never service damaged battery packs. Service of
battery packs should only be performed by the manufacturer or
authorized service providers.
Additional Specific Safety Rules for Drills/Drivers/
Impact Drills
• Wear ear protectors when impact drilling. Exposure to noise
can cause hearing loss.
• Hold the power tool by insulated gripping surfaces when
performing an operation where the cutting accessory or
fasteners may contact hidden wiring. Cutting accessory
or fasteners contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator an
electric shock.
• Use clamps or other practical way to secure and support
the workpiece to a stable platform. Holding the work by hand
or against your body is unstable and may lead to loss of control.
• Wear safety goggles or other eye protection. Hammering
and drilling operations cause chips to fly. Flying particles can
cause permanent eye damage.
• Hammer bits and tools get hot during operation. Wear
gloves when touching them.
• Do not operate this tool for long periods of time. Vibration
caused by hammer action may be harmful to your hands and
arms. Use gloves to provide extra cushion and limit exposure by
taking frequent rest periods.
• Air vents often cover moving parts and should be
avoided. Loose clothes, jewellery or long hair can be caught in
moving parts.
Safety Instructions When Using Long Drill Bits
• Never operate at higher speed than the maximum speed
rating of the drill bit. At higher speeds, the bit is likely to bend
if allowed to rotate freely without contacting the workpiece,
resulting in personal injury.
• Always start drilling at low speed and with the bit tip in
contact with the workpiece. At higher speeds, the bit is likely to
bend if allowed to rotate freely without contacting the workpiece,
resulting in personal injury.
• Apply pressure only in direct line with the bit and do not
apply excessive pressure. Bits can bend causing breakage or
loss of control, resulting in personal injury.
Residual Risks
The following risks are inherent to the use of drills:
• Injuries caused by touching the rotating parts or hot parts of
the tool.
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
• Impairment of hearing.
• Risk of squeezing fingers when changing accessories.
• Health hazards caused by breathing dust developed when
working in wood.
• Risk of personal injury due to flying particles.
• Risk of personal injury due to prolonged use.
22
Battery Type
The following tools operate on an 18 volt battery pack:
DCD791, DCD796
These battery packs may be used: DCB181, DCB182, DCB183,
DCB183B, DCB183G, DCB184, DCB184B, DCB184G, DCB185,
DCB187, DCB189, DCBP034, DCB546, DCB547, DCB548, DCB549.
Refer to Technical Data for more information.
Package Contents
The package contains:
1 Drill/driver or 1 drill/driver/hammerdrill
1 Charger (with some models)
1 Li-Ion battery pack (C1, D1, E1, L1, M1, P1, S1, T1, X1, Y1 models)
2 Li-Ion battery packs (C2, D2, E2, L2, M2, P2, S2, T2, X2, Y2 models)
3 Li-Ion battery packs (C3, D3, E3, M3, P3, S3, T3, X3, Y3 models)
1 Instruction manual
nOTE: Battery packs, chargers and kitboxes are not included
with N models. Battery packs and chargers are not included with
NT models. B models include Bluetooth® battery packs.
nOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use of
such marks by D WALT is under license. Other trademarks and
e
trade names are those of their respective owners.
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
a
Read instruction manual before use.
g
Wear ear protection.
f
Wear eye protection.
n
Visible radiation. Do not stare into light.
Date Code Position (Fig. A)
The date code , which also includes the year of manufacture,
16
is printed into the housing.
Example:
Year and Week of Manufacture
Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Trigger switch
1
Forward/reverse control button
2
Torque adjustment collar
3
Gear shifter
4
Worklight
5
Keyless chuck
6
Belt hook
7
Mounting screw
8
Bit clip
9
2023 XX XX