Fein WSG8-125 Bedienungsanleitung Seite 27

OBJ_BUCH-0000000223-002.book Page 27 Tuesday, March 1, 2016 2:32 PM
Handling hazardous dusts
For work procedures with this power tool where mate-
rial is removed, dusts develop that can be hazardous to
one's health.
Contact with or inhaling some dust types, e. g. asbestos
and asbestos-containing materials, lead-containing coat-
ings, metal, some wood types, minerals, silicate particles
from materials containing stone, paint solvents, wood
preservatives, antifouling paints for vessels, can trigger
allergic reactions to the operator or bystanders and/or
lead to respiratory infections, cancer, birth defects or
other reproductive harm. The risk from inhaling dusts
depends on the exposition. Use dust extraction matched
appropriately for the developing dust, as well as personal
protective equipment and provide for good ventilation of
the workplace. Leave the processing of asbestos-contain-
ing materials to specialists.
Wood and light-metal dust, hot mixtures of grinding dust
and chemical materials can self-ignite under unfavourable
conditions or cause an explosion. Avoid sparking in the
direction of the dust collector as well as overheating of
the power tool and the materials being sanded, empty the
dust collector/container in time, observe the material
manufacturer's working instructions, as well as the rele-
vant regulations in your country for the materials being
worked.
Operating Instructions.
The self-start lock prevents the angle grinder (see Table)
from automatically restarting again, even after a brief
interruption of the power supply, e. g., from a pulled
mains plug.
Angle grinder with self-start lock (see Table).
WSG8-115 (**)
WSG8-125 (**) In the EU
WSG11-125 (**)
Angle grinder with self-start lock and electronics (see
Table) are equipped with overload and blocking protec-
tion. In case of overload or blocking of the application
tool, the power supply is interrupted. In this case, switch
the power tool off, remove it from the workpiece and
check the application tool. Afterwards, switch the power
tool on again.
WSG12-125P (**) WSG17-150PQ (**)
WSG12-125PQ (**) WSG17-70 Inox (**)
WSG15-125P (**) WSG15-125PR (**)
WSG15-125PQ (**) WSG15-125PRT (**)
WSG15-70 Inox (**) WSG17-125PR (**)
WSG17-125P (**) WSG17-125PRT (**)
WSG17-125PQ (**) WSG17-150PR (**)
WSG17-125PS (**) WSG17-150PRT (**)
WSG17-125PSQ (**) WSG17-70 InoxR (**)
WSG17-150P (**) WSG17-70 InoxRT (**)
Press the locking button only when the motor is
stopped (see page 8).
Repair and customer service.
When working metal under extreme operat-
ing conditions, it is possible for conductive
dust to settle in the interior of the power tool.
The total insulation of the power tool can be impaired.
Blow out the interior of the power tool via the ventila-
tion slots frequently with dry and oil-free compressed air,
and connect a residual current device (RCD) on the line
side.
If the supply cord of this power tool is damaged, it must
be replaced by a specially prepared cord available through
the FEIN customer service centre.
The current spare parts list for this power tool can be
found in the Internet at www.fein.com.
If required, you can change the following parts yourself:
application tools, auxiliary handle, clamping flanges,
wheel guard
Warranty and liability.
The warranty for the product is valid in accordance with
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer's warranty declaration.
The delivery scope of your power tool may include only
a part of the accessories described or shown in this
Instruction Manual.
Declaration of conformity.
FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the last
page of this Instruction Manual.
Technical documents at: C. & E. Fein GmbH, C-DB_IA,
D-73529 Schwäbisch Gmünd
Environmental protection, disposal.
Packaging, worn out power tools and accessories should
be sorted for environmental-friendly recycling.
Selection of accessories (see page 16).
Use only original FEIN accessories. The accessories must
be intended for the power tool type.
A Grinding disc, flap disc
(use only with mounted wheel guard)
B Cutting disc
(use only with mounted cut-off wheel guard)
C Steel wire brush, fleece backing pad
D Backing pad for fibre sanding sheets, fibre sanding
sheets
(mount only with the provided backing-pad clamping
unit; use only with mounted hand guard or wheel
guard)
E Steel tapered twist brush
F Backing pad with Velcro, Velcro sanding sheets,
sanding fleece with Velcro attachment, sponges
(use only with mounted hand guard)
G Steel cup brush, round twist brushes
(use only with mounted hand guard)
en
27