EINHELL BT-JS 800 Originalbetriebsanleitung Seite 13

Anleitung_BT_JS_800_E_SPK1:_
5.5 Adapter for dust extraction system (Figure
7/Item 6)
Connect your jigsaw to a vacuum cleaner using
the adaptor for dust extraction (6). This will
provide excellent dust extraction on the
workpiece. The benefits are that you will protect
both the equipment and your own health. Your
work area will also be cleaner and safer.
Dust created when working may be dangerous.
Refer to the section entitled "Safety instructions".
Attach the adaptor (6) as shown in Figure 7, so
that it is securely seated in the housing.
Fit the vacuum tube of the vacuum cleaner onto
the adaptor opening (6). Check that the
connections are airtight.
6. Operation
6.1 ON/OFF switch (Fig. 8/Item 3)
To switch on:
Press the ON/OFF switch
To switch off:
Release the ON/OFF switch
6.2 Locking button (Fig. 8/Item 2)
You can lock the ON/OFF switch (3) using the locking
button (2) when the equipment is in operation. To
switch off the equipment briefly hold down the
ON/OFF switch (3).
6.3 Electric speed selector (Fig. 8/Item 1)
You can pre-select the required speed with the speed
selector. Turn the speed selector in PLUS director to
increase the speed and turn the speed selector in
MINUS direction to reduce the speed. The suitable
stroke speed is dependent on the relevant material
and working conditions.
General rules for cutting speeds for metal cutting
work must be complied with here as well.
You can generally use a higher speed with fine saw
blades whilst coarser saw blades require lower
speeds.
Position 1-2 = low stroke speed (for steel)
Position 3-4 = medium stroke speed (for steel, soft
metal, plastic)
Position 5-6 = high stroke speed (for softwood,
hardwood, soft metal, plastic)
12.02.2010 13:03 Uhr Seite 13
6.4 Setting the pendulum action (Fig. 3/Item 8)
The strength of the pendulum action of the saw
blade (12) can be adjusted using the selector
switch for pendulum action (8).
You can adjust the cutting speed, the cutting
performance and the finish to the workpiece you
wish to saw.
Set the selector switch for pendulum action (8) to one
of the following positions:
Position 0: No pendulum action
Material: Rubber, ceramic, aluminium, steel
Please note: For fine and clean cuts, thin materials
(e.g. sheet steel) and hard materials.
Position 1: Small pendulum action
Material: Plastic, wood, aluminium
Please note: For hard materials
Position 2: Medium pendulum action
Material: Wood
Position 3: Large pendulum action
Material: Wood
Please note: For soft materials and sawing along the
grain
The best combination of speed and pendulum action
depends on the material you wish to saw. We
recommend you to make a trial cut on a waste piece
in order to check the ideal settings.
6.5 LED lamp (Fig. 9/Item 16)
The LED lamp (16) can be used in poor lighting
conditions to additionally illuminate the cutting
position. Press the switch (17) to switch on. To switch
off, press the switch (17) again.
6.6 Making cuts
Ensure that the ON/OFF switch (3) is not
depressed. Only then should you connect the
mains plug to a suitable socket.
Do not switch on the jigsaw until you have fitted a
saw blade.
Use only saw blades that are in perfect condition.
Replace blunt, bent or cracked saw blades
immediately.
Place the saw foot flat on the workpiece you wish
to saw. Switch on the jigsaw.
Allow the saw blade to accelerate until it reaches
full speed. Then slowly move the saw blade along
the cutting line. Only exert gentle pressure on the
saw blade as you do so.
When cutting metal, apply a suitable coolant
along the line you wish to cut.
GB
13