Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
BEFORE THE FIRST USE
(E)
• Clean all the parts
with warm water and washing up liquid except for the
motor unit
(A)
which must never be immersed in water or placed under
running water (see § Cleaning).
CAUTION: The blades are extremely sharp; handle them with caution when
using or cleaning the appliance.
• Make sure all the packaging has been removed before operating the
appliance
Important note:
•
Turn the control knob
(A)
jug on the motor unit
.
• The appliance will start only if the blender jug is positioned correctly on the
motor unit.
Do not operate the appliance if the lid is not in place.
•
ASSEMBLING AND FITTING THE JUG
(e2)
• Fit the gasket seal
on the blade unit
• Place the assembly
(e1+e2)
on the base of the jug
the blade unit through a quarter turn in an anticlockwise direction
• Introduce the ingredients to the assembled jug.
• Place the lid
(e4)
on the jug. Place the measuring cup
lid.
• Place the blender jug assembly
be placed in two positions: jug handle to the right or the left of the motor unit
(Fig. 3).
USING YOUR APPLIANCE FOR THE FIRST TIME
• Once the blender jug is positioned correctly on the motor unit, plug in the
appliance and turn it on using the desired function.
Speed selection:
•
Turn the control knob
speed increases gradually between
this speed as required during preparation.
"Pulse" function:
•
Turn the control knob
succession of pulses gives finer control over the degree of blending for
precise preparations. In this position, the appliance starts directly on
maximum speed. It stops as soon as you release the knob.
(D)
to
before placing the blender
0
(e1) (Fig.1)
.
(e3)
. Lock it by rotating
(e5)
in its slot on the
(E)
(A)
on the motor unit
. The blender jug can
(D)
to choose the desired speed; the
min " "
max " ".
and
You can change
(D)
"Pulse"
to the
position. Using a
10
Function "
•
This function is used to prepare smooth milkshakes and fruit cocktails. The
speed is pre-programmed for best results. To use this function, turn the control
knob to
, and press the
0
stop it, press the
•
Function "
You can use this function to crush ice finely with pre-programmed operating
cycles and speed. To use this function, turn the control knob to
the "Ice crush" button
crush"
button
• Your appliance comes with a microprocessor that controls and analyses the
operating power.
automatically.
the appliance and remove some of the ingredients from the blender jug.
llow your appliance to cool down to room temperature. Plug it in again. You
can then select the desired speed or function to complete your preparation.
ADVICE
(Fig.2).
• Depending on the nature of the ingredients, you can use the blender jug to
prepare up to
*
1.5 L for thick mixtures
*
1.25 L for liquid preparations
• You can prepare finely blended soups, cream soups, stewed fruit, light batter
(pancakes, fritters, Yorkshire pudding batter, etc.), milkshakes, smoothies,
cocktails, etc.
• If ingredients stick to the sides of the jug when blending, stop the appliance.
Remove the blender jug from the motor unit, and push the food down onto
the blades using a spatula and put your blender jug back to continue your
preparation.
• lways pour the liquid ingredients into the blender jug first, before adding the
solid ingredients, without exceeding the maximum level.
• To add ingredients while blending, remove the measuring cup
(e4)
lid
and add the ingredients through the feeder hole.
• For finely crushed ice, use a maximum of 6 to 10 large ice cubes using
crush" function. There is no need to add water.
Smoothies"
"Smoothies"
button
"Smoothies"
(B)
button
again.
Ice crush"
(C)
to start the appliance. To stop it, press the
(C)
again.
If the load becomes too high, your appliance will stop
To restart your appliance, turn the control knob to
11
(B)
to start the appliance. To
0
, and press
"Ice
0
, unplug
(e5)
from the
"Ice
Werbung
Inhaltsverzeichnis
