Protecting The Environment; Technical Data - Black & Decker KC2002 Bedienungsanleitung

ENGLISH
When sawing wooden workpieces, it is not necessary to drill a
pilot hole:
Mark the desired starting point.
Tilt the tool forward and place the rounded front edge of
the saw shoe on the workpiece.
Switch the tool on and slowly feed the saw blade into the
workpiece at the desired starting point.
When cutting sheet metal:
Clamp a piece of plywood or soft wood to the back of the
workpiece and saw through the combination in order to
obtain a clear cut.
Do not force the saw blade into the workpiece. Note that
cutting sheet metal will normally take more time than
sawing thicker wooden workpieces.
Spread a thin film of oil along the cutting line before sawing.
To cut, switch the tool on and move it down until the saw
blade is exactly over the point of entry.
Lower the rear of the shoe towards the workpiece,
maintaining a firm pivoting pressure on the saw shoe.
With the shoe flat on the workpiece, feed the blade into
the workpiece.
When cutting laminates:
Cut thin laminates with the back surface facing up,
as splintering is most likely to occur on the side of the
workpiece facing the saw shoe.
For clean cuts, clamp a piece of plywood or hardboard to
both sides of the laminate and cut through the resulting
sandwich.
Sanding
Do not exert too much pressure on the tool.
Regularly check the condition of the sanding sheet.
Replace when necessary.
When sanding new layers of paint before applying
another layer, use extra fine grit.
On very uneven surfaces, or when removing layers of
paint, start with a coarse grit. On other surfaces, start
with a medium grit. In both cases, gradually change to a
fine grit for a smooth finish.
Consult your retailer for more information on available
accessories for sanding, polishing, stripping and scrubbing.
Maintenance
Your Black & Decker tool has been designed to operate over a
long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
8
All manuals and user guides at all-guides.com
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.

Protecting the environment

Tools
Batteries
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com.

Technical data

Voltage
Battery cat. no.
Drill/screwdriver:
No-load speed
Max. torque
Chuck capacity
Max. drilling capacity in steel/wood mm 10/25
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
from the interior.
Regularly apply a drop of light machine oil to the guide
roller (22) of the jigsaw head (fig. K).
Black & Decker provides a facility for recycling
Black & Decker products and rechargeable batteries
once they have reached the end of their working life.
This service is provided free of charge. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
Black & Decker batteries can be recharged many
times. At the end of their useful life, discard
Cd
batteries with due care for our environment:
Run the battery down completely, then remove it from the
tool.
NiCd and NiMH batteries are recyclable. Take them to
any authorised repair agent or a local recycling station.
KC2000 KC2002
V 12 14.4
DC
A9275 $
min -1 0 - 700 0 - $
Nm 6.2 $
mm 10 10
10/25