Perel EVM851 Bedienungsanleitung Seite 7

9.3 AC VOLTAGE
Do not m
Rang ge
200 V
600 V
Frequenc cy range: 40Hz
9.4 DIO ODE & CONTI
Do not c
Rang ge
9.5 RES SISTANCE
Do not c
Rang ge
200Ω Ω
2kΩ Ω
20kΩ Ω
200k kΩ
2MΩ Ω
Maximum m open circuit vo
9.6 TRA ANSISTOR h
Do
incl
Ra ange
NPN & PNP
10. Op erating ins
10.1 DC C VOLTAGE M
Do not measure D
Use extreme ca U
Always place yo A
1. Conn nect the red test
2. Set t the rotary switch
befor rehand, you sho
until the ideal resolu
3. Conn nect the test lea
4. Read d the voltage va
10.2 DC C CURRENT M
Do not measure D
Use extreme ca U
A Always place yo
1. Conn nect the red test
red le ead to the "10A
2. Set t the rotary switch
3. Open n the circuit in w
SERI IES.
4. Read d the current va
16.04.201 0
measure circuits s that may cont
Resolutio on
100mV
1V
to 400Hz.
INUITY
conduct diode- o or continuity me
If continu uity exists (less
Dis plays the diode
conduct resistan nce measureme
Resolutio on
0.1Ω
1Ω
10Ω
100Ω
1kΩ
oltage : 3.2V
FE TEST (0-1 1000)
not conduct tra nsistor measure
uded adaptor so ocket.
Tested ra ange
0-1000 0
structions
MEASUREME NT
e circuits that m may contain volta
ution when mea asuring voltages
our fingers behin nd the protectiv
t lead to the "VΩ ΩmA" jack and
h in the desired DCV position. I
ould set the ran ge switch in the
ution is obtained d.
ds to the source e being measur
lue on the LCD display along w
MEASUREME ENT
e current in circu uits with voltage
ution when mea asuring voltages
our fingers behin nd the protectiv
t lead to the "VΩ ΩmA" jack and
A" jack for meas surements betwe
h (DCA) in the d desired position
which the curren nt is to be meas
lue and the pola arity of the red
EVM8 851
ain voltages > 6 600V
± ±1.2% of rdg ± 1
easurements on n live circuits.
Description
than 60Ω), bui lt-in buzzer will
's approx. forwa ard voltage drop
nts on live circu uits.
± ±0.8% of rdg ±
± ±1.0% of rdg ±
ements on live c circuits. For tran
Tested cur rrent
Ib = 10µ µA
ages > 600V
s higher than 60 0Vdc or 30Vac r
ve edges of the
the black lead t to the "COM" jac
If the voltage to o be measured i
e highest range
red.
with the polarity
es > 250V
s higher than 60 0Vdc or 30Vac r
ve edges of the
the black test le ead to the "COM
een 200mA and d 10A).
.
sured and conne ect the test lead
lead connection n on the LCD dis
7
Accuracy y
10 digits
sound
p
Accuracy y
2 digits
2 digits
nsistor test use
T Tested voltage
Vcd = 3V
rms.
test probes whi le measuring!
ck.
is unknown
position and th en reduce grad
of the red lead connection.
rms.
test probes whi le measuring!
M" jack (switch t
ds to the circuit
splay
the
e
ually
the
IN
©Vellema an nv