Assembly And Adjustments - DeWalt DCS391NT Bersetzt Von Den Originalanweisungen

• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack with the rails inside the tool's
3
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button 13
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which consists
e
of three green LED lights that indicate the level of charge
remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button 22 . A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Trigger Switch (Fig. A)

WARNING: This tool has no provision to lock the trigger
switch in the ON position and should never be locked ON
by any other means.
Release the trigger switch lock-off button
button as shown. Pull the trigger switch
Releasing the trigger switch turns the motor off.
Depth of Cut Adjustment (Fig. A, C)
1. Loosen the depth adjustment lever
2. Move the shoe 5 to obtain the correct depth of cut.
3. Tighten the depth adjustment lever
WALT battery packs and chargers.
e
3 is fully charged.
and firmly pull the battery pack
1 by pressing the
2 to turn the motor on.
4 .
4 .
4. For optimal results, allow the saw blade to protrude from the
workpiece by about 3 mm (see inset in Figure C).
Bevel Adjustment (Fig. D)
The bevel angle can be adjusted between 0° and 50°.
1. Loosen the bevel adjustment knob
2. Set the bevel angle by tilting the saw shoe
indicates the desired angle on
the scale.
3. Tighten the bevel adjustment knob
Shoe Adjustment for 90° Cuts (Fig. D, E)
1. Adjust the saw to 0° bevel.
2. Retract the blade guard using the lever
on the blade side.
3. Loosen the bevel adjustment knob
4. Place a square against the blade and shoe to adjust the
90° setting.
5. Turn the calibration screw
the proper angle.
6. Confirm the accuracy of the setting by checking the
squareness of an actual cut on a scrap piece of material.
Rip Guide Installation and Usage (Fig. F)
Ripping is the process of cutting wider boards into narrow
strips, cutting the grain lengthways. Hand guiding is more
difficult for this type of sawing and the use of the rip guide
is recommended.

WARNING: For your own safety, read the instruction
manual before using any accessory. Failure to heed
these warnings may result in personal injury and serious
damage to the saw and accessory. When servicing this
tool, only use identical replacements.
Assembly
1. Loosen the rip guide knob
2. Insert the rip guide 16 as shown in Figure F.
3. Tighten the rip guide knob
Use the supplied rip guide only with the DCS391 circular saw.
Use of this rip guide with other saws may increase the risk of
kickback and injury.
Before making a cut, ensure the rip fence is securely fastened to
the tool.
After installing the rip guide on the saw or after moving the
guide to change the rip width setting, check the operation
of the lower guard before starting the saw and making a
cut to make sure that the rip guide does not affect proper
guard operation.
Replacing the Saw Blade (Fig. G)
1. Engage the blade lock button
clamping screw 8 by turning clockwise using the hex key
supplied with the tool.
2. Retract the lower blade guard
replace the blade. Reinstall the washers (
correct position.
EngLIsh
10 .
5 until the mark
10 .
6 and place the saw
10 .
17 so that the shoe will stop at
15 .
15 securely.
11 and unscrew the blade
7 using the lever 6 and
18 , 19 ) in the
37