Electrical Connection; Operation; Maintenance - DeLonghi HTM02 Bedienungsanleitung

ELECTRICAL CONNECTION

- Before plugging in the heater, check that the voltage of your domestic supply corre-
sponds to the voltage (V) indicated on the appliance.
- Check that the electrical socket has a rating of 10/16 Amps.
- THIS APPLIANCE COMPLIES WITH EEC DIRECTIVE 89/336, RELATING TO ELEC-
TRO-MAGNETIC COMPATIBILITY.

OPERATION.

- Summer use (ventilation only): turn the knob clockwise to the
- Heating at low power: turn the knob to the "1" position. The pilot lamp switches
on.
- Heating at maximum power: turn the knob to the "2" position. The pilot lamp
switches on.
- Setting the thermostat: when the room temperature has reached the desired
level, slowly turn the thermostat dial counter-clockwise until the pilot light goes out (or
until you hear a 'click' on models without pilot light) but no further. The thermostat will
now automatically maintain the temperature at the desired level.
- Switching the heater off: turn the knob fully counter-clockwise to the "O" posi-
tion.
- Antifreeze function (thermostat models only): turn the knob to the
The appliance will maintain a minimum room temperature of approximately 5˚C thus
preventing freezing with the minimum energy consumption.

MAINTENANCE

- Always pull the plug out of the power point before cleaning the heater.
- Periodically clean the air intake and outlet grilles during the period in
which the heater is in use with a vacuum cleaner.
- Do not use abrasive cleaning products or solvents.
CAUTION
Never use the heater near a bath, shower, basin or swimming pool.
-
- Do not use the heater to dry your laundry. Never obstruct the intake and outlet grilles
(danger of overheating).
- The heater must positioned at least 50 cm from furniture or other objects.
- If the power cable is damaged, it must be replaced by the manufacturer, an authori-
sed service centre or a qualified electrician in order to eliminate all risk.
- The appliance must not be positioned directly underneath a fixed power point.
- Do not use the appliance in rooms less than 4 m
Important: never cover the appliance when it is in operation as this could cause a fire risk.
The heater is fitted with a safety device which will switch off the heater in case of acci-
dental overheating (eg. obstruction of air intake and outlet grilles, motor turning slowly
or not at all). To reset, disconnect the plug from the power point for a few minutes, remo-
ve the cause of overheating then plug the appliance again.
Warning: in order to avoid overheating, do not cover the heater.
A) If your appliance comes fitted with a plug, it will incorporate a 13 Amp fuse. If it does not fit your socket, the plug
should be cut off from the mains lead, and an appropriate plug fitted, as below.
WARNING: Very carefully dispose of the cut off plug after removing the fuse: do not insert in a 13 Amp socket
elsewhere in the house as this could cause a shock hazard.
With alternative plugs not incorporating a fuse, the circuit must be re-fitted when changing the fuse using a 13
Amp Asta approved fuse to BS 1362. In the event of losing the fuse cover, the plug must NOT be used until a
replacement fuse cover can be obtained from your nearest electrical dealer. The colour of the correct replacement
fuse cover is that as marked on the base of the plug.
B) If your appliance is not fitted with a plug, please follow the instructions provided below:
The wires in the mains lead are coloured in accordance with the followin code:
As the colours of the wires in the mains lead of this ppliance may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which si marked with the letter L or coloured red.
ELECTRICAL CONNECTION (U.K. ONLY)
WARNING: THIS APPLIANCE MUST BE EARTHED
IMPORTANT
Blue:
Brown:
2 in area.
Neutral
Live
3
GB
position.
position.