Landmann FP-I-601CS Serie Montage- Und Gebrauchsanleitung Seite 7

NOTICES FOR SAFE OPERATION
PLEASE NOTE!
■ PLEASE NOTE: risk of carbon monoxide poisoning! Do not
operate the fire pit indoors, only outdoors!
■ Only use the fire pit if it has been assembled properly in ac-
cordance with these assembly and operating instructions and is
undamaged.
■ NOTICE: The fire pit must not be used if it is deformed or de-
fective. This must be checked before each use.
■ Before use, place the fire pit on a safe, stable, horizontal, level
and fireproof surface.
■ PLEASE NOTE! National and local regulations, such as permits,
operation, safety distances and others, must be complied with.
■ Choose the location for setting up the fire pit so that no com-
bustible materials or substances are located nearby or can get
to it. Never set up the fire pit below branches. The minimum
distance from combustible materials and surrounding surfaces
has to be 3 m.
■ PLEASE NOTE! Keep children and pets well away from the fire
pit! Never leave the fire pit unattended when it is burning or still
hot. In particular, make sure that no children or persons who
are not capable of correctly recognising or reacting to possible
dangers come near the hot fire pit.
■ PLEASE NOTE! Do not use any spirits or petrol for ignition or
reignition! Only use lighting aids that comply with EN 1860-3!
■ Only natural coniferous or deciduous wood ready for use in
the fire pit (no compressed wood products from these types of
wood) must be burnt.
■ The fire pit must not be used as a waste incinerator. No unsuit-
able or non-recommended fuels must be used. In addition, no
liquid fuels must be used.
■ PLEASE NOTE! The fire pit gets very hot and must not be
moved while in use!
■ Do not use the fire pit in strong wind.
■ Keep your distance during use. If the fire pit has to be touched,
e.g. when adding fuel, wear barbecue gloves (to prevent
thermal risks) which conform to DIN EN 407 (Category II). Even
when the fire has gone out, the surfaces will still remain hot for
some time.
■ Do not overload the fire pit and do not allow the fire to get
too big. The fire pit may be filled with a maximum of 6.5 kg of
firewood.
■ In the event of a fire: smother the flames with a suitable fire-
proof blanket or a fire extinguisher.
The fire pit may stain. You should therefore place it on a hard-wear-
ing surface or a fireproof mat.
Using petrol or spirit to ignite the fuel may result in uncontrollable
heat caused by deflagrations. You should only use safe materials for
burning, such as solid firelighters.
L
Hardwood, i.e. wood from deciduous trees such as beech,
oak or birch, is particularly suitable as firewood. Thanks to
its high density, this wood gives a long and even heat.
1. Stack some of the wood in the fire pit. Ignite one or two solid
firelighters and place them in the fire pit.
2. Allow the solid firelighters to burn for two to four minutes.
3. Carefully add more wood. Never throw wood into the fire!
03625_FP-I-601_M_V1.indb 7 03625_FP-I-601_M_V1.indb 7
AFTER USE /
CLEANING AND STORAGE
PLEASE NOTE!
■ Allow all parts to cool down completely before you clean the
product, place a cover over it or store it away.
■ Never extinguish the fire with water to avoid burns and scald-
ing.
■ Do not use corrosive or abrasive cleaning agents or brushes
with metal bristles. They may damage the surfaces.
■ Do not fill with water or expose to rainfall for a prolonged
period.
• Once all parts have cooled down, dispose of the ash in an envi-
ronmentally friendly way.
• Clean the fire pit with a suitable brush.
• Allow all parts to dry completely or dry them before they are
stored away.
• Store them in a dry, weatherproof location.
DISPOSAL
Pay attention to cleanliness when handling the product and dispos-
ing of waste materials. As a general rule, you should only dispose of
waste materials in designated metal or non-flammable containers.
The local regulations on waste disposal apply.
To dispose of the product, dismantle it into its individual parts and
recycle any metals and plastic.
Dispose of the packaging material in an environmentally
friendly manner so that it can be recycled.
EN
Made in China.
7
21.01.2022 08:41:59 21.01.2022 08:41:59