Transportation And Storage - Ryobi RXBC01 Übersetzung Der Originalanleitung

of hearing injury and the potential for other persons to
enter your working area.
■
Do not operate the product when you are tired, ill, or
under the influence of alcohol, drugs, or medication.
■
Keep all parts of your body away from any moving part.
■
Keep the cutting head attachment below waist level.
■
Never operate the product with damaged guards or
without guards in place, Ensure the correct guards are
fitted particularly.
■
Keep hands and feet away from the cutting means at
all times and especially when the product is running.
WARNING
If the product is dropped, suffers heavy impact or begins
to vibrate abnormally, immediately stop the machine and
inspect for damage or identify the cause of the vibration.
Any damage should be properly repaired or replaced by
an authorised service centre.
FOR ASSEMBLING WITH ELECTRIC-DRIVEN POWER
HEAD ONLY
■
Electrical power should be supplied via a residual
current device (RCD) with a tripping current of not more
than 30 Ma
■
If you need to use an extension cable ensure it is
suitable for outdoor use and has a current capacity
sufficient to supply your tool. Check it before every use
for damage. Always uncoil it during use because coiled
cables can overheat.
■
If the power cable becomes damaged, it must be
replaced before using.
BRUSHCUTTER SAFETY WARNINGS
■
Beware, the cutting means continue to rotate after the
motor is switched off.
■
Use heavy gloves while installing or removing blades,
they have sharp edges.
■
Do not attempt to touch or stop the blade when it is
rotating.
■
A moving blade can cause severe injury. Maintain
proper control of the machine with both hands until the
blade has completely stopped rotating.
■
Replace any blade that has been damaged. Always
make sure blade is installed correctly and securely
fastened before each use.
■
Use only the manufacturer's replacement TRI-ARC
blade. Do not use any other cutting attachment.
■
Never cut any material over 13mm diameter
■
Your Brush cutter is fitted with a harness. Carefully
adjust the harness to fit comfortably and help to support
the weight of the machine at your right side.
■
Identify the Quick Release mechanism and practice
using it BEFORE you start using the machine. Its
correct use may prevent serious injury in the case of
an emergency. Never wear additional clothing over
the harness or otherwise restrict access to the quick
release mechanism.
■
Switch off, and disconnect from power supply (if
applicable), and make sure all moving parts have come
to stop before:
●
servicing
●
leaving the product unattended
●
cleaning your product
●
clearing blockages
●
checking for any damage after hitting an object
●
checking for any damage if the product starts to
vibrate abnormally
●
performing maintenance
●
remove or install blade
■
Always ensure that ventilation openings are kept clear
of debris.
■
Before use and after any impact, check that there are
no damaged parts. Examine the cutting means for
signs of cracking or other damage. A defective switch
or any part that is damaged should be properly repaired
or replaced by an authorized service facility.
■
Do not modify the machine in any way, this may
increase the risk of injury to yourself or others.
■
Cover the blade with the blade protector before storing
the unit, or during transportation. Always remove the
blade protector before using the unit. If not removed,
the blade protector could become a thrown object as
the blade begins to turn.
■
Exercise extreme caution when using the blade with
this unit. Blade thrust is the reaction that may occur
when the spinning blade contacts anything it cannot
cut. This contact may cause the blade to stop for an
instant, and suddenly "thrust" the unit away from the
object that was hit. This reaction can be violent enough
to cause the operator to lose control of the unit. Blade
thrust may occur without warning if the blade snags,
stalls, or binds. This is more likely to occur in areas
there it is difficult to see the material being cut.
■
For cutting ease and safety, approach the weeds being
cut from the right to the left. In the event an unexpected
object or woody stock is encountered, this practice
could minimize the blade thrust reaction. Both hands
must be used at all times to control this product

TRANSPORTATION AND STORAGE

FOR ASSEMBLING WITH PETROL-DRIVEN POWER
HEAD
■
Stop the engine, and allow it to cool before storing or
transporting.
■
Clean all foreign material from the product.
■
Cover the blade with the blade protector
■
Drain all fuel from tank into a container approved for
petrol. Remember to properly replace and tighten the
fuel cap.
■
If applicable, drain all lubricant from tank into a
container approved for lubricant. Remember to properly
replace the lubricant cap.
■
Run the engine until it stops, this will remove all fuel
that could become stale and leave varnish and gum in
the fuel system.
■
Store the product in a cool dry and well-ventilated
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
English | 3