Ec Declaration Of Conformity; Cleaning And Maintenance - Bresser 7002512 Bedienungsanleitung

TROUBLESHOOTING
Problem/Symptom Solution
Strange or no measure- 1. Check drain hole in the rain collector.
ment of rain sensor
2. Check the circular level. Realign the
Strange or no measure- 1. Check radiation shield. Clean it if
ment of Thermo/Hygro neccessary.
Sensor 2. Check sensor housing. Clean it if
neccessary
1. Relocate main unit and 5-in-1 sensor
and --- (no signal
for 15 minutes)
2. Make sure the main unit is placed
and ER (no Signal for
1 hour)
3. If problem continues reset both, main
SPECIFICATIONS
Main unit
Batteries
Barometer unit
Barometer measuring range
Temperature unit
Temperature measuring range
Humidity measuring range
Time display
Time format
Calendar display
5-in-1 sensor
Batteries
Temperature unit
Temperature measuring range
Humidity measuring range
Rainfall unit
Rainfall measuring range
Wind speed unit
Wind speed measuring range
Wind direction display

CLEANING AND MAINTENANCE

Before cleaning the device, disconnect it from the power supply (remove
batteries)!
Only use a dry cloth to clean the exterior of the device. To avoid damaging
the electronics, do not use any cleaning fluid.
Cleaning the rain collector (sinkhole)
Fig. 33
N
‚Lock' position ‚Unlock' position
1. Rotate the rain collector by 30° anticlockwise.
2. Gently remove the rain collector.
18
Clean it if neccessary.
device if neccessary.
closer to each other.
away from other electronic appliances
that may interfere with the wireless
communication (TV's, computers,
microwaves).
unit and 5-in-1 sensor.
3 x AA, 1.5 V
hPa, inHg, mmHg
540 - 1100 hPa
°C / °F
-10° - 50° C
20% - 90%
HH:MM:SS
12 or 24 hours
TT/MM/JR or MM/TT/JR
3 x AA, 1.5 V
°C / °F
-40° - 60° C
1% - 99%
mm, inch
0 - 9999 mm (0 - 393.7 inch)
mph, m/s, km/h, knot
0 - 112 mph, 0 - 50 m/s, 0 - 180
km/h, 0 - 97 knots
16
N
3. Clean and remove any debris or insects.
4. Install all the parts when they are fully clean and dried.
Cleaning the thermo/hygro sensor
Fig. 34
1. Unscrew the 2 screws at the bottom of the radiation shield.
2. Gently pull out the shield.
3. Remove carefully any dirt or insects inside the sensor casing
NOTE!
The radiation shield comprises different parts inserted one inside
another. Two bottom parts are closed. Do not change their order!
Do not let the sensors inside get wet!
4. Clean the shield with water and remove any dirt or insects.
5. Install all the parts back when they are fully clean and dried.
DISPOSAL
Dispose of the packaging materials properly, according to their type,
such as paper or cardboard. Contact your local waste-disposal
service or environmental authority for information on the proper disposal.
Do not dispose of electronic devices in the household garbage!
As per Directive 2002/96/EC of the European Parliament on waste
electrical and electronic equipment and its adaptation into German law,
used electronic devices must be collected separately and recycled in an
environmentally friendly manner.
In accordance with the regulations concerning batteries and
rechargeable batteries, disposing of them in the normal household
waste is explicitly forbidden. Please make sure to dispose of your used
batteries as required by law — at a local collection point or in the retail
market. Disposal in domestic waste violates the Battery Directive.
Batteries that contain toxins are marked with a sign and a chemical
symbol. "Cd" = cadmium, "Hg" = mercury, "Pb" = lead.

EC DECLARATION OF CONFORMITY

Bresser GmbH has issued a "Declaration of Conformity" in accordance
with applicable guidelines and corresponding standards. This can be
viewed under www.bresser.de/download/7002512/CE/7002512_CE.pdf.