Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
en
ENGLISH
The fine mesh filter prevents coarse particles from
entering the motor housing. Remove regularly and
clean.
- Two hole nut (22)
- Multi-position bar (25) for side handle
Permits numerous handle positions.
Order no.: 627362000
- Hand protection (26)
Intended for work with backing pads, hook and loop
packing pads (sanding pads), wire brushes and
diamond drill bits for tiles.
Install the hand guard under the additional side-
mounted handle.
Order no.: 630327000
- Battery packs:
Order no.: 625368000 5.5 Ah (LiHD)
Order no.: 625369000 8.0 Ah (LiHD)
Order no.: 625549000 10.0 Ah (LiHD)
etc.
- Chargers: ASC 55, ASC 145, etc.
Extraction guard for surface grinding may
only be used in conjunction with the 2-
hole nut
For a complete range of accessories, see
www.metabo.com or the catalogue.
12. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
13. Environmental Protection
The sanding dust generated may contain
hazardous materials: do not dispose of dust with
household waste, but at a special collection point
for hazardous waste.
Packaging materials must be disposed of according
to their labelling in accordance with municipal
guidelines. Further information can be found at
www.metabo.com in the "Service" section.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Battery packs must not be disposed of with regular
waste! Please return faulty or used battery packs to
your Metabo dealer!
Do not throw battery packs into water.
Only for EU countries: never dispose of
power tools in your household waste!
According to European Directive 2012/19/EU
on Waste from Electric and Electronic Equipment
and implementation in national law, used power
tools must be collected separately and recycled in
an environmentally-friendly manner.
Discharge the battery pack in the power tool before
22
disposal. Prevent the contacts from short-circuiting
(e.g. by protecting them with adhesive tape).
14. Technical Data
Explanatory notes on the specifications on page 2.
Subject to change in accordance with technical
progress.
U
= Voltage of battery pack
D
=max. diameter of accessory
max
t
= max. permitted thickness of the clamping
max,1
shank on accessory when using two-hole
nut (22)
t
= max. permitted thickness of the clamping
max 2
shank on accessory when using a quick
clamping nut (1)
t
= roughing disc/cutting disc:
max,3
max. permitted thickness of accessory
t
= max. permitted thickness of wheel-
max,4
type wire brushes
M
= Spindle thread
l
= Length of the sanding spindle
n
= No-load speed (maximum speed)
n
= no-load speed (adjustable)
v
m
= Weight (with smallest battery pack)
Measured values determined in conformity with
EN 62841.
direct current
The technical specifications quoted are subject to
tolerances (in compliance with relevant valid
standards).
The grinding of thinner metal sheets and other
workpieces with large surfaces that easily
vibrate can lead to a significantly higher overall
sound emission (up to 15 dB) than the sound
emission values specified. The sound radiation of
such workpieces should be prevented to the
greatest extent possible by means of suitable
measures, such as fitting heavy, flexible damping
mats. The increased sound emission must also be
taken into account when assessing the risk of noise
exposure and selecting suitable hearing protection.
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on operating conditions, the
condition of the power tool or the accessories used.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user, such as
organisational measures based on the adjusted
estimates.
Total vibration value (vector sum of three directions)
determined in accordance with EN 62841:
a
= Vibration emission value (surface
h, SG
grinding)
a
= vibration emission value (sanding
h, DS
with hook and loop sanding pad)
K
= Uncertainty (vibration)
h,SG/DS
Typical A-effective perceived sound levels:
L
= sound pressure level
pA
L
= acoustic power level
WA
K
, K
= Uncertainty
pA
WA
Werbung
Inhaltsverzeichnis
