Before Starting The Equipment - EINHELL TP-ET 18 Li BL Originalbetriebsanleitung

5. Before starting the equipment

Warning!
Always pull out the battery before making ad-
justments to the equipment.
All covers and safety devices must be properly
fi tted before the equipment is switched on.
5.1 Fitting the extraction socket
(Fig. 1.2/Item 11)
Caution! For health and safety reasons it is
imperative that you use a dust extractor.
•
Connect your cordless tool to a domestic
vacuum cleaner or a dust extractor using
the extraction socket (11). This will ensure
optimum dust extraction from the workpiece.
The benefits are that you will protect both the
equipment and your own health. Your work
area will also be cleaner and safer.
•
Dust created when working may be dange-
rous. Refer to the section entitled "Safety inst-
ructions".
•
The vacuum cleaner you use for the vacuum
extraction must be suitable for the material
you are machining. Use a special vacuum
cleaner if you are handling harmful materials.
Cordless palm router (Fig. 1.2/Item 11)
•
Secure the extractor adapter (11) to the
palm router insert (20) using the countersunk
screw (12).
•
The extractor adapter can be connected to
extractor units (vacuum cleaners) with a suc-
tion hose.
•
The internal diameter of the extractor adapter
is 36 mm. Now fit a suction hose of matching
size to the extractor adapter.
5.2 Fitting the parallel stop (Fig. 3/ Item 19)
•
Undo the fastening screw for the routing gui-
de (10).
•
Insert the parallel stop (19) in the holder for
the routing guide (10) as shown in Fig. 3 and
retighten the fastening screw for the routing
guide (10).
•
Set the parallel stop (19) to the required di-
mension and secure it in place with the wing
screw (c).
5.3 Fitting the compass point (Fig. 4/Item 18)
•
You can cut circular areas using the compass
point (18).
•
To do so, undo the wing nut (c) and remove
Anl_TP-ET_18_Li_BL_Solo_SPK13.indb 21 Anl_TP-ET_18_Li_BL_Solo_SPK13.indb 21
GB
the front section of the parallel stop (19).
•
Screw-fit the compass point (18) on the par-
allel stop (19) as shown in Fig. 5. Now fit the
parallel stop (19) together with the compass
point (18) on the router.
•
The procedure for fitting is the same as de-
scribed in section 5.2 except that the parallel
stop (19) must be turned through 180° so that
the compass point (18) points downwards
(Fig. 4).
•
Set the required radius between the compass
point (18) and the cutter.
•
Position the compass point (18) in the center
of the circle you wish to cut.
5.4 Fitting and using the copy sleeve
(Fig. 5-8/Item 14)
•
Remove the four recessed head screws (d)
from the bottom of the palm router insert and
take off the cover (e) (Fig. 5).
•
Insert the copy sleeve (14) as shown in Fig. 6.
•
Refit the cover (e) using the four recessed
head screws (d).
•
The copy sleeve (14) will be guided along the
template (g) by the guide ring (f).
•
To obtain an exact copy the workpiece (h)
must be larger by the difference between the
"external edge of the guide ring" and the "ex-
ternal edge of the cutter" (i).
5.5 Fitting/removing the cordless routing unit
(Fig. 9)
Warning! Remove the battery.
•
To insert the cordless routing unit (1) in the
palm router insert (20), first undo the faste-
ning screw for the depth adjuster (8) and then
insert the cordless routing unit (1).
•
Then use the height adjuster (9) and the sca-
le (22) to set the required cutting depth.
•
Finally retighten the fastening screw for the
depth adjuster (8).
5.6 Fitting/removing the cutting tool
(Fig. 10- 14)
Warning! Remove the battery.
Caution! When you have fi nished working
with the palm router, the cutting tool will stay
very hot for a relatively long time!
Caution! Cutters are very sharp. Wear protec-
tive gloves at all times when handling cutting
tools.
•
To make it easier to change the cutter, re-
move the cordless routing unit (1) from the
- 21 -
12.07.2022 09:06:49 12.07.2022 09:06:49