Before Starting The Equipment; Operation - EINHELL CE-AP 18 Li Originalbetriebsanleitung

5. Before starting the equipment

This product is supplied without batteries and wit-
hout a charger and is allowed to be used only with
the lithium-ion batteries of the Power-X-Change
series!
5.1 Charging the lithium-ion battery pack
(Fig. 3.4)
1. Pull the battery pack out of the handle, pres-
sing the pushlock button (C) downwards
while you do so.
2. Check that your mains voltage is the same as
that marked on the rating plate. Insert the po-
wer plug of the charger into the socket outlet.
The green LED will begin to blink.
3. Push the battery pack onto the battery char-
ger.
In the section entitled „Charger indicator" you will
fi nd a table with an explanation of the LED indica-
tor on the charger.
If the battery pack fails to charge, check for the
following:
•
Is there voltage at the power socket
•
Is there good contact at the charger's char-
ging contacts
If the battery pack still fails to charge, please send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.2 Battery capacity indicator (Fig. 5)
Press the button for the battery capacity indicator
Anl_CE-AP_18_Li_Solo_SPK13.indb 17 Anl_CE-AP_18_Li_Solo_SPK13.indb 17
GB
(A). The battery capacity indicator (B) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
5.3 Fitting a battery (Fig. 3)
Push the battery into the battery mount provided.
When the battery is positioned as in Fig. 3, make
sure that the pushlock button (C) latches in place!
To remove the battery, proceed as described in
section 5.1.

6. Operation

Warning!
•
The equipment does not have an automatic
cut-out. You must therefore monitor the com-
plete inflation and deflation process.
•
Do not exceed the inflation pressure recom-
mended by the manufacturer in any circum-
stances. If inflated objects burst they can
cause serious injuries.
•
Never insert any objects in the blow connec-
tor or the suction connector. Do not cover the
air openings.
•
Never direct the air outlet towards eyes while
the equipment is working.
•
To prevent overheating, allow the equipment
to cool down after every 20 minutes of ope-
ration.
•
In the event of overloading, switch off the
equipment immediately and allow it to cool.
6.1 Switching on and off (Fig. 1)
•
To activate the equipment briefly, press and
hold the switch (Item 5) lightly.
•
Press the switch (Item 5) to switch on the
- 17 -
29.07.2021 15:20:28 29.07.2021 15:20:28