Werbung
E N G L I S H
Two-Wire Indoor Staton
Diagram References
Appearance
1
1
2
Microphone
3
Debugging Port
4
Alarm Terminal
Display Screen
5
Two-Wire Interface
6
Loudspeaker
7
Power Supply Interface
Note: The debugging port is used for debugging only.
2
Wiring
AIN1: Alarm Input 1
AIN7: Alarm Input 7
AIN2: Alarm Input 2
AIN8: Alarm Input 8
AIN3: Alarm Input 3
GND: Grounding
AIN4: Alarm Input 4
485-: RS-485 Interface
AIN5: Alarm Input 5
485+: RS-485 Interface
AIN6: Alarm Input 6
Note: Wiring descripton refers to the User Manual.
Installaton
3
The wall mountng plate and the juncton box are required to install the indoor staton onto
the wall.
The dimension of juncton box should be 75 mm (width) × 75 mm (length) × 50 mm (depth).
The dimension of wall mountng plate is shown.
Before you begin:
1. Make sure the device in the package is in good conditon and all the assembly parts
are included.
2. The power supply the indoor staton supports is 12 VDC. Please make sure your
power supply matches your indoor staton.
3. Make sure all the related equipment is power-off during the installaton.
4. Check the product specificaton for the installaton environment.
5. Here takes wall mounitng with juncton box for example.
Wall Mountng with Juncton Box
1. Chisel a hole in the wall. The size of the hole should be 76 mm (width) × 76 mm
(length) × 50 mm (depth).
2. Insert the juncton box to the hole chiseled on the wall.
3. Fix the wall mountng plate to the juncton box with 2 screws.
4. Hook the indoor staton to the wall mountng plate tghtly by insertng the plate hooks
into the slots on the rear panel of the indoor staton, during which the lock catch will be
locked automatcally.
Wall Mountng without Juncton Box
1. Insert 2 expension tubes into the wall.
2. Fix the wall mountng plate to the wall with 2 screws.
3. Hook the indoor staton to the wall mountng plate tghtly by insertng the plate
hooks into the slots on the rear panel of the indoor staton, during which the lock
catch will be locked automatcally.
Getng Started
4
Actvate Indoor Staton
1
You are required to actvate the device first by setng a strong password for it before
you can use the device.
1. Power on the device. It will enter the actvaton page automatcally.
2. Create a password and confirm it.
3. Tap OK to actvate the indoor staton.
Note: We highly recommend you to create a strong password of your own choosing
(using a minimum of 8 characters, including at least three kinds of following categories:
upper case leters, lower case leters, numbers, and special characters) in order to
increase the security of your product. And we recommend you reset your password
regularly, especially in the high security system, resetng the password monthly or
weekly can beter protect your product.
2
Quick Configuraton
1. Choose Language and tap Next.
2. Set network parameters and tap Next
- Edit Local IP, Subnet Mask and Gateway parameters.
- Enable DHCP, the device will get network parameters automatcally.
3. Configure the indoor staton and tap Next.
a. Select Indoor Staton Type.
b. Edit Floor and Room No.
4. Linked related devices and tap Next. If the device and the indoor staton are in the
same LAN, the device will be displayed in the list. Tap the device or enter the serial No.
to link.
a. Tap the door staton in the list to link.
b. Tap the setngs icon to pop up the Network Setngs page.
c. Edit the network parameters of the door staton manually or enable DHCP to get
the network parameters automatcally.
d. Optonal: Enable Synchronize Language to synchronize the Language of door
staton with indoor staton.
e. Tap OK to save the setngs.
5. Tap Finish to save the setngs.
The power supply must conform to LPS. The recommended adaptor models and
manufacturers are shown as below. Use the atached adaptor ,and do not change the
adaptor randomly.
Model
Current
Manufacturer
MSA-C1500CS24.0-40W-DE
1.5A
MOSO POWER SUPPLY TECHNOLOGY CO.,LTD
ADS-40FSI-19 24036EPG
1.5A
SHENZHEN HONOR ELECTRONIC CO.,LTD
1
3
122
Safety Instruction
Warnings
● All the electronic operaton should be strictly compliance with the electrical safety regulatons, fire preventon regulatons
and other related regulatons in your local region.
● Please use the power adapter, which is provided by normal company. The power consumpton cannot be less than the
required value.
● Do not connect several devices to one power adapter as adapter overload may cause over-heat or fire hazard.
● Please make sure that the power has been disconnected before you wire, install or dismantle the device.
● When the product is installed on wall or ceiling, the device shall be firmly fixed.
● If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please
contact the service center.
● If the product does not work properly, please contact your dealer or the nearest service center. Never atempt to
disassemble the device yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or
maintenance.)
Cautons
● Do not drop the device or subject it to physical shock, and do not expose it to high electromagnetsm radiaton. Avoid the
equipment installaton on vibratons surface or places subject to shock (ignorance can cause equipment damage).
● Do not place the device in extremely hot (refer to the specificaton of the device for the detailed operatng temperature),
Standard
cold, dusty or damp locatons, and do not expose it to high electromagnetc radiaton.
● The device cover for indoor use shall be kept from rain and moisture.
CE
● Exposing the equipment to direct sun light, low ventlaton or heat source such as heater or radiator is forbidden
(ignorance can cause fire danger).
CE
● Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a
malfuncton however), and affectng the endurance of sensor at the same tme.
● Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the
acidic sweat of the fingers may erode the surface coatng of the device cover.
● Please use a sof and dry cloth when clean inside and outside surfaces of the device cover, do not use alkaline
detergents.
● Please keep all wrappers afer unpack them for future use. In case of any failure occurred, you need to return the device
to the factory with the original wrapper. Transportaton without the original wrapper may result in damage on the device
and lead to additonal costs.
● Improper use or replacement of the batery may result in hazard of explosion. Replace with the same or equivalent type
only. Dispose of used bateries according to the instructons provided by the batery manufacturer.
3 4 5
1
2
Note: Do not wire the cables through the cable
7
hole (red area) when installing the device with
gang box.
Lock Catch
Lock Catch
Lock Catch
Lock Catch
Unit:mm
Rear Panel (without Interface)
Consignes de sécurité
Avertssements :
● Tous les éléments électroniques doivent respecter à la letre la réglementaton locale sur la sécurité des
installatons électriques, sur la préventon des incendies et des réglementatons connexes en vigueur.
● Utlisez un adaptateur fourni par une entreprise agréée. La consommaton électrique ne doit pas êttre inférieure à la
valeur exigée.
● Ne branchez pas plusieurs appareils sur un mêtme adaptateur ; toute surcharge de l'adaptateur pouvant entraîner
sa surchauffe ou provoquer un incendie.
● Veillez à bien déconnecter la source d'alimentaton avant de câbler, installer ou démonter l'appareil.
● Lors de l'installaton au mur ou au plafond, assurez-vous que l'appareil est bien fixé.
● Si l'appareil dégage de la fumée ou une odeur suspecte, ou s'il émet des bruits inhabituels, éteignez-le et
débranchez le câble d'alimentaton, puis contactez le SAV.
● Si le produit ne fonctonne pas correctement, contactez votre revendeur ou le SAV le plus proche. Vous ne devez en
aucun cas essayer de démonter le produit vous-mêtme. (Nous déclinons toute responsabilité en cas de problèmes
découlant d'une interventon ou d'une réparaton effectuée sans autorisaton.)
Précautons
● Évitez de faire tomber l'appareil, de le heurter et de l'exposer à des rayonnements électromagnétques de forte
intensité. Évitez d'installer l'équipement sur des surfaces vibrantes ou à des emplacements subissant des chocs
fréquents (au risque de l'endommager).
● N'installez pas l'appareil à un emplacement trop chaud ou trop froid (reportez-vous à la spécificaton de l'appareil
pour connaître la température de fonctonnement précise), poussiéreux ou humide. Ne l'exposez pas non plus à des
rayonnements électromagnétques élevés.
● Le capot de l'appareil pour installaton intérieure ne doit pas êttre exposé à la pluie, ni à l'humidité.
● Il est formellement interdit d'exposer l'équipement directement au soleil, à un environnement mal ventlé ou à une
source de chaleur telle qu'une chaudière ou un radiateur (au risque de provoquer un incendie).
● N'orientez pas l'appareil vers le soleil ou des sources de lumière très vive. Dans le cas contraire, un voile ou des
traînées risquent de se former (ce qui ne consttue toutefois pas un dysfonctonnement) et la résistance du capteur peut
également êttre affectée.
● Utlisez le gant fourni pour ouvrir le capot du dmme et évitez tout contact direct avec celui-ci, l'acidité de la sudaton
des doigts pouvant éroder le revêttement du capot de l'appareil.
● Utlisez un chiffon doux et sec pour netoyer les surfaces intérieures et extérieures du capot de l'appareil. N'utlisez
pas de détergents alcalins.
● Conservez tous les emballages ; ils pourront vous resservir ultérieurement. En cas de panne, renvoyez l'appareil à
l'usine dans son emballage d'origine. Si l'appareil est transporté hors de son emballage d'origine, il risque d'êttre abîmé,
entraînant des frais supplémentaires.
● Une mauvaise utlisaton de la baterie ou un remplacement erroné peut entraîner un risque d'explosion. Ne la
remplacez que par une baterie identque ou de type équivalent. Metez les bateries usagées au rebut conformément
aux instructons du fabricant.
2
ALARM IN
6
Hook
Hook
Hook
Hook
Screw
Wall Mountng Plate
Juncton Box
Product Informaton
About this Manual
The Manual includes instructons for using and managing the product. Pictures, charts, images and all other
informaton hereinafer are for descripton and explanaton only. The informaton contained in the Manual is
subject to change, without notce, due to firmware updates or other reasons. Please find the latest version in
the company website.
Please use this user manual under the guidance of professionals.
Legal Disclaimer
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR
OWN RISKS. OUR COMPANY SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY
LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR
OTHER INTERNET SECURITY RISKS; HOWEVER, OUR COMPANY WILL PROVIDE TIMELY TECHNICAL SUPPORT IF
REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION
BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. OUR
COMPANY SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
Data Protecton
During the use of device, personal data will be collected, stored and processed. To protect data, the
development of our devices incorporates privacy by design principles. For example, for device with facial
recogniton features, biometrics data is stored in your device with encrypton method; for fingerprint device,
only fingerprint template will be saved, which is impossible to reconstruct a fingerprint image.
As data controller, you are advised to collect, store, process and transfer data in accordance with the applicable
data protecton laws and regulatons, including without limitaton, conductng security controls to safeguard
personal data, such as, implementng reasonable administratve and physical security controls, conduct periodic
reviews and assessments of the effectveness of your security controls.
RS485
Wall
Werbung
