Declaration Of Conformity (Doc) - Conrad 97 52 26 Bedienungsanleitung

Configuration of the Client by means of WPS
Please note:
In order to be able to use the WPS function, the router which shall be connected to
the device, must support WPS. Furthermore, with this configuration method a PC or
laptop is not required. The Client can be used directly on the corresponding device
after successful configuration.
• First, activate WPS on your router.
• Following this, press the WPS button on the Client for approx. 2-3 seconds, until the middle
LED starts to flash slowly.
• Now both devices attempt to establish an encrypted connection. This process may take
several minutes.
• Once a connection has been established, the WPS LED lights continually again.
• Now you can use the device as described below.
Connection of the Client to another Network Device
The following description refers to a Playstation 3.
• Connect the converter's LAN interface "Ethernet" via a 1:1 connected network cable with the
network port on the PS3.
• Then connect the USB power cable to the Client's power connector and to a USB port on the
PS3.
• Switch the PS3 on. Once the system has loaded, wireless access to the Internet and to the
available network will be possible.
LEDs on the Client
Power LED lights if the router is switched on; flashes rapidly during reset of the device.
WPS The LED flashes slowly, when WPS is activated.
WLAN LED is lit, when WLAN reception is turned on.
Resetting the Client
Press and hold down the "RESET" button for approx. 3 seconds using a sharp object.
Only release the button again, when the power LED starts flashing rapidly.
The device then restarts. The process takes approx. 30 seconds. After this, the Client is reset to
the factory settings (IP 192.168.1.249, DHCP on), user name "admin" and password "password".
Furthermore, all of your settings will have been deleted.
Handling
Only to be used in dry indoor locations. The product must not get damp or wet.
Never use the product immediately after it has been taken from a cold room to a
warm one. The condensation that forms might destroy your unit. Allow the device to
reach room temperature before switching it on. This may take several hours. Only
when this has been done, put the device into operation.
Ensure that the insulation for the entire product is neither damaged nor destroyed.
The housing must not be opened! Any maintenance or repair work may only be
carried out by authorised personnel.
Check the product for damage before use! If you notice any damage, the product
must NOT be used.
It can be assumed that safe operation is no longer possible if
- the device is visibly damaged,
- the device does not operate any longer and
- the device has been stored under unfavourable conditions for a long period of time
or
- it has been subjected to considerable stress during transportation.
Avoid the following adverse conditions at the installation location and during trans-
portation:
- Excessive humidity or damp
- Extreme cold (<0°C) or heat (>45°C), direct sunlight
- Dust or flammable gases, fumes or solvents
- Strong vibrations, impacts or blows,
- Strong magnetic fields such as those found in the vicinity of machinery or loud-
speakers
When setting up the product, make sure that the cables are neither kinked nor
pinched.
Cleaning
Use a clean, dry soft cloth for cleaning. Do not use any aggressive cleaning agents as these may
result in discoloration of the enclosure.
Disposal
Electrical and electronic products do not belong in the household waste!!
Please dispose of the device when it is no longer of use, according to the current
statutory requirements.

Declaration of conformity (DOC)

The manufacturer hereby declares that this product adheres to the fundamental requirements
and the other relevant regulations of Directive 1999/5/EC.
You can find the Declaration of Conformity for this product on the Internet at
www.conrad.com.
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or
the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2010 by Conrad Electronic SE.