Maintenance And Servicing; Maintenance And Cleaning - Bosch GAS 18V-10 L Professional Originalbetriebsanleitung

18 | English
Attaching the Carrying Strap (see figure E)
Click the snap hooks of the carrying strap (30) into the
lugs (9) of the dust extractor.
Fitting the Rollers (see figure F)
Insert the 4 fastening pins on the rollers (31) into the roller
adapters (32) until they audibly click into place.
Other rollers can also be used as per the EN 12529 standard
(11 mm fastening pin diameter).
Check the functionality of the roller brakes before us-
u
ing the dust extractor.
Operation
Remove the battery before cleaning or performing
u
maintenance on the dust extractor, making tool ad-
justments, changing accessories or placing the dust
extractor in storage. This safety measure prevents the
dust extractor from being started accidentally.
Ensure that the work area is clean and tidy to minim-
u
ise the risk of tripping.
Start-up
The dust extractor must not be used without a filter.
u
Before extraction, ensure that the filter unit is se-
u
curely fitted.
Before extraction, ensure that the battery compart-
u
ment cover is securely closed.
Please inform yourself about the applicable regula-
u
tions/laws on how to handle harmful types of dust in
your country.
Only vacuum rock dust with the power tool and dust
u
extraction system combination explicitly identified,
for which it has been proven that the legal thresholds
are not exceeded. You can find this evidence at
http://www.bosch-professional.com/dust.
The dust extractor must categorically not be used in poten-
tially explosive areas.
To ensure optimum suction power, you must always fully un-
wind the vacuum hose (13) from the vacuum hose
bracket (23).
For safety reasons, the dust extractor does not switch on if
the on/off button (3) is held down for longer than five
seconds.
Do not use damaged filters (e.g. no cracks, small
u
holes, etc.). Replace any damaged filters immedi-
ately.
Dry Vacuuming
Vacuuming up Dust Deposits
– To switch on the dust extractor, briefly press the on/off
button (3).
– To switch off the dust extractor, press the on/off but-
ton (3) again.
1 609 92A 5KE | (20.04.2020)
Extracting dust that accumulates from working power
tools (see figure G)
There must be a sufficient air exchange rate (L) in the
u
room when the exhaust air comes back into the room.
Be aware of the corresponding national regulations.
– Fit the dust extraction adapter (14) or the curved
nozzle (15) (see "Fitting the extraction adapter or curved
nozzle (see figure D)", page 17).
– Insert the extraction adapter (14) or the curved
nozzle (15) into the power tool's dust extraction outlet.
Only when using the dust extraction adapter (14):
Note: When working with power tools that have a low air
feed into the vacuum hose (e.g. jigsaws, sanders, etc.), the
false air intake (26) of the dust extraction adapter (14) must
be opened. This will improve the total output of the dust ex-
tractor and the power tool. To do this, turn the ring above
the false air intake (26) until the opening is at its maximum
size.
Wet Vacuuming
Do not use the vacuum cleaner to vacuum combustible
u
or explosive liquids, such as petrol, oil, alcohol or
solvents. Do not vacuum hot or burning dust. Do not
operate the vacuum cleaner in areas subject to explo-
sion hazards. Dust, vapours and liquids can ignite or ex-
plode.
Before wet vacuuming:
– Empty the container (1).
– Clean the filter (27) and fit it back into the dust extractor
(see "Cleaning/replacing filters (see figures I1–I2)",
page 19).
The dust extractor is equipped with a float. Extraction is
stopped when the maximum filling level is reached.
After wet vacuuming, always:
– Empty the container (1).
– Empty the water from the filter (27).
To prevent mould growth after wet vacuuming:
– Remove the dust extractor lid (5) and leave it to dry thor-
oughly.
– Remove the filter (27) and also leave this to dry thor-
oughly (see "Cleaning/replacing filters (see figures I1–
I2)", page 19).

Maintenance and Servicing

Maintenance and Cleaning

Remove the battery before cleaning or performing
u
maintenance on the dust extractor, making tool ad-
justments, changing accessories or placing the dust
extractor in storage. This safety measure prevents the
dust extractor from being started accidentally.
To ensure safe and efficient operation, always keep
u
the dust extractor and the ventilation slots clean.
Bosch Power Tools