Specified Conditions Of Use - AEG PS 216 L Originalbetriebsanleitung

Pay attention to blade packing and unpacking, it is easy to be
injured by the sharp blade tips.
Use a blade holder or wear gloves when handling a saw blade.
Keep and store the blade in original packaging or other suitable
packaging, keep in dry conditions and away from chemicals which
may damage the blade.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Always clamp the workpiece safely and securely.
Ensure that the machine is always stable and secure (e.g. xed to
a bench).
Wear ear protectors. Exposure to noise can cause hearing loss.
Always wear safety goggles when using the machine. It is recom-
mended to wear gloves for handling blades and rough material,
as well as sturdy non-slip shoes which also protect the feet from
workpieces that may fall from the cutting area.
Always make sure the power plug has been removed from the
mains power source before making adjustments, lubricating or
when doing any maintenance on the product.
GB
Only plug-in when machine is switched o .
Never reach into the area near the blade, unless the blade has
completely stopped.
Before use, thoroughly check the tool for any damage or material
fatigue. Repairs should only be carried out by authorised Service
Agents.
Always use the guards on the machine. Do not use the machine if
the guards are not in place and working correctly.
The lower blade guard should only open when the blade is lowered
to the workpiece and must always be able to move freely and close
automatically..
Always x and use extension bar holders for workpiece support
during operation.
Never alter of modify the saw or its function. Your safety may be
compromised.
Do not use saw blades which are cracked, damaged, or deformed.
Do not use saw blades made of high-speed steel.
Only use saw blades which are sharp. Replace blunt blades with a
new replacement.
Always use blades with correct size and shape of arbour holes.
Blades that do not match the mounting hardware of the saw will
run eccentrically, causing loss of control.
Use only woodworking blades speci ed in this manual, which
comply with EN 847-1.
Do not use any anges, washers, and nuts to secure the saw blade
other than those supplied or indicated in the instruction manual.
It is necessary to select a saw blade which is suitable for the mate-
rial being cut. Never use the product to cut materials other than
those speci ed in the intended use section in this manual.
It is important to avoid overheating the blade and melting the
plastic workpiece when cutting.
It is essential to adhere to the maximum speed speci ed on the saw
blade. only use saw blade that are marked with a speed equal or
higher than the speed marked on the tool.
Replace the table insert when worn or damaged.
Before work, make a dummy cut without the motor turned on so
the position of the blade, operation of the guards with respect to
other machine parts, and workpiece may be checked.
English
32
When performing mitre, bevel or compound mitre cuts, adjust the
sliding fence to ensure the correct clearance from the blade.
The bracket stop must always be engaged when transporting the
product.
Keep the oor area free of loose material e.g. chips and cut-o s.
Refrain from removing any cut-o s or other parts of the workpiece
from the cutting area whilst the machine is running and the saw
head is not in the rest position.
Long workpieces must be adequately supported.The working
area of the saw includes the whole extent of the workpiece. The
operator should secure this area from accidental contact from
other persons or objects which may move the workpiece during
operation.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Use a dust absorption system and wear a
suitable dust protection mask. Remove deposited dust thoroughly,
e.g. with a vacuum cleaner.
Do not replace the LED or laser with a di erent type. Any repairs
must only be carried out by the manufacturer or authorised service
agent.
A power spike causes voltage uctuations and may a ect other
electrical products in the same power line. Connect the product
to a power supply with an impedance equal to 0.3 to minimize
voltage uctuations. Contact your electric power supplier for
further clari cation.
SAFETY WARNINGS LASER
The laser radiation used in this saw is Class II with maximum P≤1mW
and λ:650nm wavelengths. Do not view directly with optical
instruments. Failure to comply with the rules could result in serious
personal injury.
Do not stare into beam during operation.
Do not project the laser beam directly into the eyes of others. Serious
eye injury could result.
Do not place the laser in a position that may cause anyone to stare
into the laser beam intentionally or unintentionally.
Do not use optical tools to view the laser beam.
Do not operate the laser around children or allow children to operate
the laser.
Do not attempt to repair the laser device by yourself.
Do not attempt to change any parts of the laser device by yourself.
Any repairs must only be carried out by the manufacturer or autho-
rised service agent.
Do not replace the installed laser with a di erent type.

SPECIFIED CONDITIONS OF USE

The slide compound mitre saw is intended for sawing solid and
bonded wood with or without glued veneer, plastics, and materials
similar to wood.
The slide compound mitre saw is intended to be used only by adult
operators who have read the instruction manual and understand
the risks and hazards.
The slide compound mitre saw is designed to be xed at the base
to a solid bench top. If the base is not securely xed, the whole
machine may move during cutting operations, which increases the
possibility of serious personal injury.
The slide compound mitre saw is designed make bevel and mitre
cuts. The capacities for the various cuts are provided in the product
speci cations in this manual.