Additional Safety Rules For Tool - Makita 2704 Betriebsanleitung

14. Maintain tools with care.
Keep cutting tools sharp and clean for better and safer
performance. Follow instructions for lubrication and
changing accessories. Inspect tool cord periodically
and if damaged have it repaired by an authorized ser-
vice facility. Inspect extension cords periodically and
replace, if damaged. Keep handles dry, clean and free
from oil and grease.
15. Disconnect tools.
When not in use, before servicing and when changing
accessories such as blades, bits and cutters.
16. Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool before
turning it on.
17. Avoid unintentional starting.
Do not carry a plugged-in tool with a finger on the
switch. Ensure switch is off when plugging in.
18. Use outdoor extension leads.
When tool is used outdoors, use only extension cords
intended for outdoor use.
19. Stay alert.
Watch what you are doing. Use common sense. Do
not operate tool when you are tired.
20. Check damaged parts.
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to deter-
mine that it will operate properly and perform its
intended function. Check for alignment of moving
parts, free running of moving parts, breakage of parts,
mounting and any other conditions that may affect its
operation. A guard or other part that is damaged
should be properly repaired or replaced by an autho-
rized service center unless otherwise indicated in this
instruction manual. Have defective switches replaced
by an authorized service facility. Do not use the tool if
the switch does not turn it on and off.
21. Warning.
The use of any accessory or attachment, other than
those recommended in this instruction manual or the
catalog, may present a risk of personal injury.
22. Have your tool repaired by a qualified person.
This electric tool is in accordance with the relevant
safety requirements. Repairs should only be carried
out by qualified persons using original spare parts,
otherwise this may result in considerable danger to
the user.
ADDITIONAL SAFETY RULES
FOR TOOL
SAVE THESE INSTRUCTIONS.
1. Wear eye protection.
2. Don't use the tool in presence of flammable liq-
uids or gases.
3. NEVER use the tool with an abrasive cut-off wheel
installed.
4. Check the blade carefully for cracks or damage
before operation. Replace cracked or damaged
blade immediately.
5. Use only saw blades recommended by the manu-
facturer and which conform to EN847-1, and
observe that the riving knife must not be thicker
than the width of the cut by the saw blade and not
thinner than the body of the blade.
6. Always use accessories recommended in this
manual. Use of improper accessories such as
abrasive cut-off wheels may cause an injury.
7. Select the correct saw blade for the material to be
cut.
8. Do not use saw blades manufactured from high
speed steel.
9. To reduce the emitted noise, always be sure that
the blade is sharp and clean.
10. Use correctly sharpened saw blades. Observe the
maximum speed marked on the saw blade.
11. Clean the spindle, flanges (especially the install-
ing surface) and hex nut before installing the
blade. Poor installation may cause vibration/wob-
bling or slippage of the blade.
12. Use saw-blade guard and riving knife for every
operation for which it can be used, including all
through sawing operations. Always install the
blade guard following the instructions out-lined in
this manual. Through sawing operations are those
in which the blade cuts completely through the
workpiece as in ripping or cross cutting. NEVER
use the tool with a faulty blade guard or secure the
blade guard with a rope, string, etc. Any irregular
operation of the blade guard should be corrected
immediately.
13. Immediately reattach the guard and riving knife
after completing an operation which requires
removal of the guard.
14. Do not cut metals such as nails and screws.
Inspect for and remove all nails, screws and other
foreign matter from the workpiece before opera-
tion.
15. Remove wrenches, cut-off pieces, etc. from the
table before the switch is turned on.
16. NEVER wear gloves during operation.
17. Keep hands out of the line of the saw blade.
18. NEVER stand or permit anyone else to stand in
line with the path of the saw blade.
19. Make sure the blade is not contacting the riving
knife or workpiece before the switch is turned on.
20. Before using the tool on an actual workpiece, let it
run for a while. Watch for vibration or wobbling
11