Installation - Conrad AMZH-1623/SW-08-1 Bedienungsanleitung

O P E R A T I N G I N S T R U C T I O N S
IP Power Strip
„AMZH-1623/SW-08-1"
Item-No. 97 24 31
Intended Use
The product uses a RJ45 network connector with switchable power distribution. The 8IEC-
plugs, are intended to be used to turn connected consumer loads on or off, via the network,
by means of suitable cable connections.
This product complies with the applicable National and European requirements. All names
of companies and products are the trademarks of the respective owner. All rights reserved.
Package Contents
• IP power strip
• Fixing bracket with screw set
• CD with software and detailed manufacturer's instructions in English
• Quick guide
Safety Instructions
The warranty will be void in the event of damage caused by failure to
observe these safety instructions. Liability forany and all consequential
damage is excluded!
We do not accept liability for damage to property or personalinjury caused
by improper handling or non-compliance with the safety instructions. The
warranty will be void in such cases.
Dear Customer,
these safety instructions are not only to protect the product but also for your own
safety and that of other people. Therefore, please read this chapter very care-
fully before using the product for the first time!
• The unauthorised conversion and/or modification of the product is inadmissi-
ble because of safety and approval reasons (CE). Do not open/disassemble!
It does not contain any internal parts that need to be adjusted or maintained by
you.
• The product's construction conforms to protection class I. It is only to be used
with an earthedmains socket connected to the public power supply. For the
permitted operating voltage for the product, please refer to the chapter
„Technical Data" at the end of this operating manual.
• Never touch the product when your hands are wet. Danger of a life-threaten-
ing electric shock!
• The product must not get damp or wet, it is only intended for use in dry, indoor
locations. Danger of a lifethreatening electric shock!
Further, protect the product from direct solar radiation, strong heat (>35°C),
cold (<0°C), dust and dirt, splashes and dripping water, vibrations or mechan-
ical loads.
• When the product is taken from a cold to a warm room (e.g. during transport),
condensation may be produced. This could damage the product. This might
cause a lethal electric shock!
Therefore, you should allow the product to warm up to room temperature
before using it or connecting it to an electric socket. This may take several
hours.
• Do not operate the product if it is damaged.
Do not touch the product, if it is damaged. First, switch off the appropriate mains
socket (e.g. via the respective circuit-breaker) and then carefully pull the mains
plug from the socket. Never operate the product if the housing or the connecting
cable/plug is damaged; there is the risk of a life-threatening electric shock!
• The product is only suitable for use in temperate, not tropical, climates.
• Never pour liquids over electrical devices and never place objects filled with
liquid on top of them (e. g. vases). You run the risk of causing a fire or a fatal
electric shock!
If this is the case, isolate the appropriate mains socket (e.g. switch off at the
circuit breaker) and then disconnect the product from the power supply.
Disconnect all cables from the device. Afterwards, the product can no longer
be used; take it to a specialistworkshop.
www.conrad.com
Version 09/09
°

Installation

The product should be mounted in a fixed location, in a so-called network cabinet.
Therefore, there are appropriate mounting options on the left and on the right; two fixing-
brackets and suitable screws are supplied.
Pay attention when tightening the screws that no cables or wires are damaged;
Connection
• If there are any devices already connected to the IP power strip, unplug them first.
• Connect the RJ45 network connector on the back of the IP powerstrip to your network;
e.g. a free port on a network switch.
• The plug's earth contact must only be connected to a standard mains socket with pro-
tective earth. The IPpower strip's indicator then lights up.
Software Installation
• After connecting the IP power strip, insert the CD, included in the delivery, into the appro-
priate drive of your computer. If the installation program does not start automatically, run
the program „Amazing.exe" from the main folder of the CD. Then click on „Install" and, in
the next window, on „1. Amazing PDU".
In case of newer CD versions, the procedure may be different.
• Thereafter, Microsoft .NET Framework may be installed (if it is not yet installed in your
operatingsystem) and then the necessary database is installed; this may take some time.
• After the installation is complete, you will find a new item in the Start menu, which you
can use to run the („Amazing PDU") software.
When you run the software for the first time, the database can be organised, or alterna-
tively, the standard settings can be used (click on „No" in the choice box, you will thus ini-
tialise the default values, which you can change later).
If you selected the software's default settings of the software (if you clicked on „No" in the
previous window), then you must enter a user name („User Name") and a password
(„Password"). Default setting on delivery is:
User name („User Name"):
Password („Password"):
Configuration
• The default setting for the IP power strip is the fixed IP address 192.168.0.216 (subnet-
mask 255.255.255.0). To access the IPpower strip, the computers in the network must
be set to the same address range 192.168.0.
If the IP address is to be used by a DHCP server, then press and hold the „FUNCTION"
key until 4 beeps sound. Then immediately release the button.
Now unplug the IP power strip for a few seconds from the powersupply and connect it
again to the mains socket. The IP power strip now receives the address from a DHCP
server.
• Do not place naked flames such as burning candles on the device or in its
vicinity.
• Do not bend the cables and do not place objects on them.
• Ensure there is adequate ventilation for the device during operation.
• Never overload the product. Please comply with the max. powerinput for the
device and its individual outputs (e.g. printed on the device).
• Never use the product in hazardous areas.
• This product is not a toy, it is not suitable for children. Children cannot judge
the dangers involved when handling electrical devices.
• Do not leave packing materials unattended. They may become dangerous
playthings for children.
• In commercial institutions, the accident prevention regulations of the
Employerís Liability Insurance Association for Electrical Systems and
Operating Materials are to be observed.
• In schools, educational centres, hobby and self-help workshops the operation
of the product is to be supervised by trained employees.
• Handle the product with care, it can be damaged by impacts, blows, or acci-
dental drops, even from a low height.
• If you have doubts about how the product should be operated or how to safe-
ly connect it, consult a qualified specialist.
• If you have any questions that are not answered in this instruction manual,
please contact our technical support centre or consult a professional.
admin
1234