Conrad RSLT4 Bedienungsanleitung Seite 3

O P E R A T I N G I N S T R U C T I O N S
2 Channel Radio Wall Switch RSLT4
Item-No. 64 66 55
Intended Use
This 2-channel wireless wall switch is designed to turn on and off two suitable receivers (e.g. wire-
less power socket, wireless outdoor socket, wireless inbuilt switch etc.). In addition, this 2-channel
wireless wall switch has a dimming function (for example, to control a wireless plug-in dimmer, wire-
less inbuilt dimmer etc.).
For each control channel, a maximum of 10 receivers can be programmed.
The 2-channel wireless wall switch is only intended for use in dry indoor locations.
The wireless wall switch is powered by a 12 V battery (type: 27A).
All the safety and operating instructions in this manual must be followed carefully. These instruc-
tions not only protect the device but, in particular, your health. Please read through all of the ope-
rating manual before using the product.
This product complies with the applicable National and European requirements. All
names of companies and products are the trademarks of the respective owner.
All rights reserved.
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions. Liability for any and all consequential damage is
excluded!
We do not accept liability for damage to property or personal injury caused
by improper handling or non-compliance with the safety instructions. The
warranty will be void in such cases.
• The unauthorized opening, conversion and/or modification of this product is not
permitted because of safety and approval reasons (CE).
• Do not use this product in hospitals or medical institutions. Although the product
emits only relatively weak radio signals, these may lead to the malfunction of life-
support systems. The same may be the case in other areas.
• The wireless wall switch is powered by a 12 V battery (type: 27A).
• The product is not a toy and must be kept out of the reach of children. Therefore,
be especially careful when children are around.
• The wireless wall switch is only intended for use in dry indoor locations.
• Do not leave packing materials unattended. They may become dangerous play-
things for children.
• Handle the product with care, it can be damaged by impacts, blows, or accidental
drops, even from a low height.
• To avoid overheating, do not cover the item with any objects, such as a curtain
for example.
• Do not use the product in the immediate vicinity of a bathtub, a shower or a swim-
ming pool.
• Do not install the product directly beneath a wall socket.
• Do not put the product in to use if it is damaged.
• Pull the mains plug out of the mains socket before cleaning the product.
• Do not use the product in combination with a timer, a separate remote control or
other means to automatically switch on the product. This might cause a fire if the
product is covered or wrongly set up.
Battery notes
• Batteries should be kept out of the reach of children.
• Please pay attention to the correct polarity (plus/+ and minus/-) when inserting the battery.
• Do not leave batteries lying around in the open; there is a risk of them being swallowed by chil-
dren or domestic animals. If swallowed, consult a doctor immediately.
• Leaking or damaged batteries can lead to caustic burning of the skin. Therefore, use suitable
protective gloves.
• Make sure that the battery is neither short-circuited nor thrown into a fire. There is a risk of
explosion!
• Do not recharge normal batteries. There is a risk of explosion! Only charge rechargeable bat-
teries that are intended for this purpose; use a suitable battery charger.
• If it is not to be used for a while (e.g. storage), remove the battery. Old batteries may leak and
cause damage to the product, which will lead to the loss of the warranty/guarantee.
• For the environmentally friendly disposal of batteries and rechargeable batteries, please read
the chapter „Disposal".
Installation and Connection
www.conrad.com
Version 06/10
°
• Carefully lift the front cover of the wireless wall switch (e.g.
with a screw driver) and remove it (see the picture on the
right).
• Remove the mounting plate. The mounting plate for the wire-
less wall switch is attached to the electronic part of the wire-
less wall switch by 4 clamps (see the picture on the right).
• The mounting plate has two fixing holes (see picture on the
right). Remove the mounting plate and mark the mounting
holes on the wall.
• Drill the mounting holes.
• Attach the mounting plate to the wall, using suitable mounting
material.
• Attach the electronic part of the wireless wall switch to the
mounting plate.
• Insert a 12V-battery (type: 27) into the battery compartment of
the wireless wall switch, paying attention to the correct polarity.
• Attach the front plate to the wireless wall switch.
Programming a receiver for the wireless wall switch
For each control channel, a maximum of 10 receivers can be programmed.
• Set the receiver to the programming mode. Please follow these operating instructions when so
doing.
• Press the desired „I" button on the wireless wall switch to which the receiver is to be programmed.
The programming has been completed successfully.
Deleting programmed receivers from the wireless wall switch
• Press the buttons „I" and „O" on the wireless wall switch to which the receiver is programmed.
The LED on the receiver starts flashing.
• Now press the button „O" on the wireless wall switch. The LED on the receiver goes out. The
receiver has now been deleted from the wireless wall switch.
The wireless wall switch's dimmer function
• Turn on the dimmer, by briefly pressing the „I" button on the wireless wall switch once.
• Press the „I" button on the wall switch again. The dimmer function is activated.
• Press the „I" button on the wall switch again. The dimmer function is deactivated.
Start-up, Function Test
Commission the receiver in the correct way (follow the receiver's operating instructions).
By pressing the appropriate „I" or „O" button on the wireless wall switch, the receiver is turned
on or off.
Maintenance and Care
The product does not require any maintenance and should never be opened or disassembled
for any reason.
Clean the product with a soft, clean and dry cloth. Never use aggressive cleaning agents or che-
mical solutions since these might damage the surface of the casing or impair the operation.
The wireless wall switch is only intended for use in dry indoor locations.
Picture similar
Picture similar
Picture similar