Herunterladen Inhalt Inhalt Diese Seite drucken

Ironing Without Steam; Vertical Steam - Bosch sensixx B45L Gebrauchsanleitung

Vorschau ausblenden Andere Handbücher für sensixx B45L:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
or (model dependent)
Quickly press the steam release button (13) on the
bottom of the handle twice (double-click)
Remarks:
• It is possible to stop the shots of steam by quickly
pressing the steam button again.
• Some water drops may appear when you use the
"Pulse steam" function for the irst time.
The water drops will disappear after you have
used the function for some time.
Ironing without steam
This enables the iron to be used for dry ironing.
1. Begin ironing but without pressing the steam
release buttons (13-14*).
Vertical steam
This can be used to remove creases from hanging
clothes, curtains etc.
It cannot be used on a synthetic setting for
delicate items.
Warning!:
• Never direct the steam jet at garments that are
being worn.
• Never aim the steam at people or animals.
1. Set the temperature to the
2. Hold the iron in an upright position setting 15 cm
away from the garment being steamed.
3. You can steam iron curtains and hanging garments
(jackets, suits, coats...) by placing the iron in a
vertical position and pressing the steam release
button (13 or 14*).
Energy saving "eco" button
(model dependent)
If the "Energy saving" button (7) is switched on, you
can save up to 25% of the energy and 40% of the
water consumption (*), and still achieve good results
when ironing most of your garments.
It is advisable to use the normal energy setting only
for thick and very wrinkled fabrics.
(*) In comparison to the maximum setting.
Note:
If you work with the "Energy saving" function,
the variable steam regulation and temperature
regulation can still be used as recommended.
"secure" auto shut-off
(model dependent)
If during ironing, the steam release button (13-14*) on
the iron handle is not pressed for a certain length of
time (8 minutes), the steam station will automatically
switch off.
The "
been activated.
To switch the steam station back on, press the steam
release button again.
Fabric protection soleplate cover (E)
(model dependent)
The fabric-protection soleplate cover is used for steam
ironing delicate garments at maximum temperature
(D)
without damaging them. Use of the soleplate cover
also does away with the need for a cloth to prevent
shine on dark materials.
It is advisable to irst iron a small section on the inside
of the garment to see if it is suitable.
To attach the soleplate cover to the iron, place the tip
of the iron into the end of the soleplate cover and pull
the elastic strap over the lower rear of the iron until
it its tightly. To release the soleplate cover, pull the
elastic strap and remove the iron.
setting.
The fabric-protection soleplate cover may be purcha-
sed from the customer service or specialist shops :
Descaling the ilter
and the boiler (F)
(Calc'n'Clean)
To extend the life of your steam generator and to
avoid any build up of scale, it is essential that you
rinse out the ilter (12) and the boiler after several
hours of use (approximately after 50 hours). If the
water is hard, increase the frequency.
Do not use descaling agents for rinsing out the boiler,
as they could damage it.
If the "
boiler must be rinsed. Please proceed as follows:
1. Check carefully that the appliance is cold and
unplugged for more than 2 hours, and that the
water tank (1) is empty.
2. Fix the iron to the stand by inserting the tip of the
iron into the front slot and moving the ixation lever
(10) against the heel of the iron.
3. Place your appliance over a sink or bucket.
" icon will lash when auto shut-off has
Accessory code
Name of accessory
(After-sales)
(Specialist outlets)
571510
" icon lashes, this indicates that the
TDZ2045

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis