EINHELL TE-CS 18/89 Li Originalbetriebsanleitung Seite 19

6.2 Using the cordless mini hand-held circu-
lar saw
•
Select a suitable blade for the material you
wish to saw.
•
Check the condition and sharpness of the
blade.
•
Set the cutting depth.
•
Pick up the tool and make sure that no air
vents are covered.
•
Switch on the tool and wait for a few seconds
for the blade to reach operating speed.
•
Push the saw forwards through the workpie-
ce. Never cut backwards!
•
Exert only little pressure on the tool when cut-
ting.
•
The base plate must always lie flat on the
workpiece.
•
Before you start your sawing work on the
workpiece, you can raise the soleplate (6)
with the lever (5) as shown in Fig. 6. This
requires you to press the locking button (3).
Starting the sawing work is then easier when
you want to begin at the edge of a workpiece.
6.3 Switching ON/OFF (Fig. 12)
To switch on:
Press the locking button (3) and the ON/OFF
switch (2) at the same time
•
Allow the saw blade to accelerate until it
reaches full speed. Then slowly move the saw
blade along the cutting line. Only exert gentle
pressure on the saw blade as you do so.
To switch off :
Release the locking button and ON/OFF switch
•
If you release the handle the equipment will
shut down automatically which means that it
cannot operate accidentally.
•
Ensure that you do not cover or block the ven-
tilation openings whilst working with the tool.
•
Do not slow down the saw blade after you
switch it off by pressing it sideways.
•
Important! Do not put down the machine until
the saw blade has reached a complete stand-
still.
Anl_TE-CS_18_89_Li_SPK13.indb 19 Anl_TE-CS_18_89_Li_SPK13.indb 19
GB
6.4 Fitting the saw blade (Fig. 1, 7-9)
Warning!
Always remove the battery before making
adjustments to the tool.
Use only saw blades which comply with standard
EN 847-1 and are of the same type as the saw
blade supplied with this circular saw. Ask your
dealer for advice.
Caution! For safety reasons the mini hand-held
circular saw must not be operated with the hex
key inserted in it.
•
With the spindle lock (14) pressed, slacken
the screw for securing the saw blade (12) by
turning it in a clockwise direction using the
hex key (c).
•
Remove the screw for securing saw blade
(12) and the underlying flange (13).
•
With the locking button (3) pressed, use the
lever (5) to raise the adjustable soleplate (6)
and hold it there.
•
Fit the saw blade. Pay attention to the running
direction (see arrow on the housing (d) and
on the saw blade)!
•
Place the flange (13) on the saw blade, ensu-
ring that you fit it correctly (see Fig. 9)
•
Then, with the spindle lock (14) pressed, tigh-
ten the screw for securing the saw blade (12)
and check that the blade runs true.
•
Before you press the On/Off switch, make
sure that the saw blade is correctly fitted and
that moving parts run smoothly and the clam-
ping screws are tightened securely.
6.5 Charging the LI battery pack (Fig. 10-11)
1. Remove the battery pack (e) from the handle,
pressing the pushlock buttons (f) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(i) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 "Charger indicator" you will fi nd a
table with an explanation of the LED indicator on
the charger.
- 19 -
20.07.2022 09:57:55 20.07.2022 09:57:55