Ryobi EID-1052RE Bedienungsanleitung Seite 8

EID-1052RE manual
GB
F D E
THANK YOU FOR BUYING A RYOBI PRODUCT.
To ensure your safety and satisfaction, carefully read
through this OWNER'S MANUAL and the SAFETY
INSTRUCTIONS before using the product.
DESCRIPTION
A. Trigger Switch
B. Forward / Reverse Button
C. Keyless Chuck
D. Variable Speed Selector
E. Lock Button
F. Drill mode shift knob
G. Depth Stopper
H. Gear setting button
I. Auxiliary Handle
J. Bit
K. Air Vents
INSTRUCTIONS FOR SAFE HANDLING
WARNING
When using electric tools, basic safety
precautions, including the following, should
always be followed to reduce the risk of fire,
electric shock and personal injury.
Make sure that the tool is only connected to the voltage
marked on the name plate.
Never use the tool if its cover or any bolts are missing.
If the cover or bolts have been removed, replace them
prior to use. Maintain all parts in good working order.
Always secure tools when working in elevated positions.
Never touch the blade, drill bit, grinding wheel or
other moving parts during use.
Never start a tool when its rotating component is
in contact with the work piece.
Never lay a tool down before its moving parts have
come to a complete stop.
ACCESSORIES: The use of accessories or attachments
other than those recommended in this manual might
present a hazard.
REPLACEMENT PARTS: When servicing use only
identical replacement parts.
Keep work area clean. Cluttered areas and benches
invite injuries.
Consider work area environment. Do not expose
power tools to rain. Do not use power tools in damp
or wet locations. Keep work area lit. Do not use
power tools where there is risk to cause fire or shock
12/09/03 10:02 Page 5
I P NL S
English
DK N FIN GR H
Guard against electric shock. Avoid body contact with
earthed or grounded surface (e.g. pipes, radiators,
ranges, refrigerators).
Keep children away. Do not let visitors touch
the tool or extension cord. All visitors should be kept
from area.
Store idle tools. When not it use, tools should be stored
in a dry, high or locked up place, out of reach of children
Do not force the tool. It will do the job better and safer
at the rate for which it was intended.
Use the right tool. Do not force small tools or
attachments to do the job of a heavy duty tool.
Do not use tool for purposes not intended.
Use safety glasses. Also use face or dust mask if
the cutting operation is dusty.
Do not abuse the cord. Never carry the tool by the cord
or yank it to disconnect it from the socket. Keep the cord
away from heat, oil and sharp edges.
Do not overreach. Keep proper footing and balance
at all times.
Maintain tool with care. Keep cutting tools sharp
and clean for better and safer performance. Follow
instructions for lubrication and changing accessories.
Inspect tool cord periodically and if damaged have
it repaired by an authorized service facility. Inspect
extension cords periodically and replace, if damaged.
Keep handles dry, clean and free from oil and grease
Disconnect tools. When not in use, before servicing
and when changing accessories such as blades, bits
and cutters.
Avoid unintentional starting. Do not carry a plugged-in
tool with a finger on the switch. Ensure switch is off
when plugging in.
Use outdoor extension leads. When tool is used
outdoors, use only extension cords intended
for outdoor use.
Stay alert. Watch what your doing. Use common sense.
Do not operate tool when you tired.
Check damaged parts. Before further use of the tool,
a guard or other part that is damaged should be
carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment breakage of parts, mounting and any other
conditions that may affect its operation. A guard or other
parts that is damaged should be properly repaired
or replaced by an authorized service centre unless
otherwise indicated in this instruction manual.
Have defective switches replaced by an authorized
service facility. Do not use the tool if the switch does
not turn it on and off.
5
CZ RUS RO PL