EINHELL FORTEXXA 18/20 TH Originalbetriebsanleitung Seite 23

ly in the guide groove of the cutter rail.
Notes on tensioning the chain:
The saw chain must be properly tensioned to
ensure safe operation. You can tell that the chain
tension is perfect if the saw chain can be lifted
by around 3-4 mm in the middle of the cutter rail.
As the saw chain heats up during cutting and
thus changes in length, please check the chain
tension every 10 minutes and adjust it again as
required. This applies in particular to new saw
chains. When you have fi nished working slacken
the chain again, as the chain will shorten when it
cools down. This will prevent the chain from being
damaged.
5.3 Saw chain lubrication
Warning! Always pull out the battery before per-
forming any checks or adjustments. Always wear
protective gloves when working on the chainsaw
to protect yourself against injury.
Notice! Never operate the chain if it is not lub-
ricated with saw chain oil. Use of the chainsaw
without saw chain oil or if the oil level is below
the "min" mark (Fig. 10/ Item B) will damage the
chainsaw.
Notice! Be aware of the temperature conditions:
diff erent lubricants with completely diff erent
viscosities are required at diff erent ambient tem-
peratures. At lower temperatures you will need
low viscosity oils in order to achieve a suffi cient
lubricating fi lm. However, if the same low viscosity
oil is used during the summer it will become even
thinner due to the ambient temperatures alone,
and as a result the lubricating fi lm could break
down, causing the chain to overheat and become
damaged. In addition, the chain oil would burn
and produce unnecessary pollutants.
Filling the oil tank:
•
Keep away from ignition sources.
•
Place the chainsaw on a flat surface.
•
Clean the area around the oil tank cover (Fig.
10/Item 7) and then clean the oil tank cover.
•
Fill the tank with saw chain oil. In the process,
make sure that no dirt enters the tank, as this
could cause the oil nozzle to become blo-
cked.
•
Close the oil tank cover.
Anl_Fortexxa_18_20_TH_SPK13.indb 23
GB
5.4 Charging the Li battery pack (Fig. 11-12)
The battery is protected from exhaustive dischar-
ge. An integrated protective circuit automatically
switches off the equipment when the battery is
fl at.
Warning! Do not actuate the On/Off switch any
more if the protective circuit has tripped. This may
damage the battery.
1. Remove the battery pack from the handle,
pressing the pushlock button (13) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(18) into the socket outlet. The green LED will
then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 12 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
- 23 -
23.11.2021 10:19:58