Installation Instructions; Installation And Setting; Sound Test; Operation - Scheppach TIGER 2000S Original Bedienungsanleitung

9.

Installation instructions

9.1 Installation and setting

Please make sure that your grinding machine stands
upright and stable on a solid surface with sufficient
lighting.
The machine has no front or rear side. Grinding can take
place either with or against the direction of rotation.
Tools required for all assembly / adjustment steps:
• Open-ended spanner 19 mm (not included in the
scope of delivery)
The grindstone is not pre-assembled for packaging
reasons
m Warning!
Do not connect the device to the power supply until
assembly is complete. Failure to do so may result in
accidental starting and possibly serious injury.

9.2 Sound test

Check the grindstone for cracks and perform a sound
test for crack detection.
• The grindstone must be removed from the machine
for the sound test. The grindstone stands upright on
the floor. On a hard floor, use a piece of wood as a
support. The grindstone must be dry.
• Lightly tap the grinding disc with a non-metallic ham-
mer. A crack-free disc has a high, purely bell-like
sound. A disc that has a crack produces a muffled
sound. If the grindstone is flawless, it can be fitted.
9.3 Installing the grindstone (Fig. 2+3)
Only use grindstones with identical technical data (see
10. Technical data).
• Remove the nut (11) with an open-ended spanner,
the outer washer (9) and the cardboard transport
sleeve of the grinding shaft (10). To do so, firmly
hold the star grip for the leather honing wheel (14).
Attention: Left-handed thread.
• The water tank (8) must be removed. (see 9.4)
• Place the grindstone on the grinding shaft (10). The
inner washer must be behind the grindstone.
• Fit the grindstone (12) as shown in Fig. 2.
• Fasten the grindstone with the washer (9) and the
nut (11) using an open-ended spanner. To do so,
firmly hold the star grip of the leather honing wheel
(14). Attention: Left-handed thread.
9.4 Fitting the workpiece support (1) (Fig. 4 + 5)
The workpiece support (1) can be attached both to the
upper mount for workpiece support (2) and to the side
mount for workpiece support (15). This depends on
whether you wish to work with or against the grinding
direction.
9.4.1 Fitting the upper mount
• To attach the workpiece support (1) to the upper
mount for workpiece support (2), first attach the two
loose star grip screws (3). Screw them into the upper
workpiece support (2) (threaded hole) at the intend-
ed position with approx. 2-3 turns.
• Then insert the workpiece support into the holes of
the upper mount for workpiece support (2).
• Fasten this at the desired height with the two star
grip screws (3).
9.4.2 Fitting the side mount
• The two star grip screws (3) for the side mount for
workpiece support (15) are pre-assembled.
• To mount the workpiece support (1) here, insert the
workpiece support into the holes in the side mount
for workpiece support (15).
• The workpiece support (1) is now fixed for the first
step.
9.5 Installing the water tank (Fig. 6 + 7)
• Attach the water tank (8) in the lowest position to the
brackets for the water tank (16) (behind the grind-
stone) on the machine housing (5). (Fig. 6)
• Then fill the tank with water up to the recess. (Fig. 7)

10. Operation

ATTENTION!
Remove the mains plug before any maintenance, mod-
ification and assembly work.
10.1 Grinding direction (Fig. 4 + 5)
This primarily depends on whether you wish to work
with or against the grinding direction.
If you wish to remove large quantities of steel quickly
(e.g. from very old, rusty tools) or if you want to grind
coarse tools such as axes, it is advisable to work
against the grinding direction.
If you wish to grind more accurately, we recommend
working with the grinding direction. This applies, for ex-
ample, when grinding tools and blades.
www.scheppach.com GB | 25