Installation Without Base; Chicco Bebècare; Safety Warnings - Chicco Oasys 0+ UP BebeCare Bedienungsanleitung

B (Fig. 5). All manuals and user guides at all-guides.com
3. Remove the child car seat as illustrated
above by pressing button P.

2.2 INSTALLATION WITHOUT BASE

To install the child car seat without the base,
proceed as follows:
1. Position the child car seat on the selected
car seat (Fig. 15) rear facing.
2. Pull the vehicle safety belt and fasten it
to the relevant buckle, inserting the hori-
zontal (waist) part of the belt through the
child car seat's two blue slots (K) (Fig. 15).
3. Take the diagonal car safety belt and
thread it through the relevant blue slot (O)
on the back of the child car seat's backrest
(Fig. 16) WARNING! When travelling by car,
this diagonal safety belt must ALWAYS be
threaded through this slot.
4. Pull the belt as tightly as possible, without
leaving any slack and making sure it is
not twisted.
5. Turn the carry handle to position A (Fig. 17).
To remove the child car seat:
1. Release the car safety belt by pressing
the buckle.
2. Bring the carry handle into the position
B (vertical).
3. Unthread the belt through the diagonal
and horizontal slots.
3. CHICCO BEBÈCARE
Chicco BebèCare was designed and devel-
oped to signal the presence of the baby in
the car seat and to notify the user when ac-
cidentally moving away from the car without
the baby, thanks to the presence of sensors
integrated in the car seat.
Chicco BebèCare was designed and devel-
oped for use only with minors with a total
weight between 4 and 13 kg.
DISCLAIMER
• The use of this equipment does not replace
in any manner the responsibility and/or
supervision of the vehicle driver (and/or
its occupants). Chicco BebèCare represents
only a support tool: Never leave the child
unattended in the car.
• Artsana cannot be held liable in any man-
ner in the case of damaging events and/or
consequences (also related to the incorrect
operation of the electronic equipment)
of any type, as Chicco BebèCare is solely
intended to be an aid and alarm to prevent
events and/or consequences caused by
forgetfulness.
• Chicco BebèCare does not prevent the risk
of serious injuries or death. The use of the
equipment does not in any way replace
the supervision and responsibility of the
driver/caregiver/supervisor/tutor or anyone
who is taking care of the baby.

SAFETY WARNINGS

• For the correct use of the car seat, please
refer to the instructions included in this
manual.
• The sensors are built into the seat section.
• Chicco BebèCare functions only if the fabric
lining of the car seat adheres perfectly to
the body of the car seat.
• Chicco BebèCare only works if the layer
between the sensor and the cover remains
in its original position (Fig. 35).
• After cleaning the fabric lining (CLEANING
THE FABRIC LINING), check that Chicco
BebèCare is functioning correctly.
• When performing cleaning or maintenance
operations, do not move and/or remove
the layer between the sensor and the co-
ver (Fig. 35).
• When cleaning/servicing the car seat, do
not disassemble the Chicco BebèCare
components. The equipment may only be
replaced if the battery is low and according
to the instructions that will be provided by
Customer Service.
• Make sure that the car seat does not come
into contact with any type of liquid. If liq-
uid comes into contact with the sensor
positioned on the seat and the wetting
is limited, dry it carefully and delicately
clean the surface of the sensor using a
dry cloth do not move and/or remove the
layer between the sensor and the cover at
any time. Wait and check again that Chicco
BebèCare functions correctly. If it does
not work or in the case of doubt, contact
Customer Service.
• If the car seat comes into contact with any
type of liquid, Chicco BebèCare may stop
to work temporarily until the car seat has
dried completely.
24