Operation; Cleaning And Maintenance; Storage/Transport - Scheppach bgs 700 Original Bedienungsanleitung

Then remove the flange (B) and replace the grind-
ing wheel (6). The grinding wheel is mounted with the
help of a rag. Mount the flange (B) on the shaft and
screw on the nut (A) hand-tight (Fig. 8).
To tighten the nut (A), hold the grinding wheel (6) with
a rag and tighten the nut (A) (Fig. 8).
Changing the grinding/sanding belt (Fig. 1/10-12)
• Loosen the fastening screw for side cover (12) and
remove the side cover (13).
• Slacken the clamp screw for the top belt roller (11)
by a few turns.
• Push the top belt roller downwards and pull the
grinding/sanding belt out off the rollers.
• Place the new grinding/sanding belt (9) in the
center of the top and bottom rollers and release the
clamping top belt roller.
• Now tighten the clamp screw for the top belt roller
(11) and fit the side safety guard.
• With the belt guidance adjustment screw (10) on
the side you can adjust the belt run by turning. Pre-
cise adjustment of the belt run is best done by turn-
ing the grinding/sanding belt by hand.
m Attention!
After replacing the grinding wheel or sanding belt, all
guards must be reassembled.

8. Operation

On/Off switch (16)
• To switch on the equipment set the On/Off switch
(16) to position 1.
• Move the On/Off switch (16) to position 0 to switch
off the equipment. After switching on, wait for the
equipment to reach its maximum speed of rotation.
Only then should you begin with the grinding.
Grinding
• Place the workpiece onto the workpiece support (8)
and slowly guide the workpiece towards the grind-
ing wheel (6) at the desired angle to the point where
workpiece and grinding wheel make contact.
• Move the workpiece slightly back and forth to pro-
duce an optimal grinding result. This way the grind-
ing wheel (6) will be evenly worn. Allow the work-
piece to cool down occasionally.
Grinding/sanding with the belt
• Always hold the workpiece firmly during grinding/
sanding.
• Do not exert excessive pressure.
• The workpiece should be moved on the belt to pre-
vent the paper wearing on one side.
• Important! Pieces of wood should always be sand-
ed with the grain to prevent them splitting.
22 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Using the grinding wheel dresser
The grinding wheel dresser is a tool for straightening
of grinding wheels.
• Press lightly against grinding wheel – without cre-
ating sparks. Move the dresser sideways over the
entire width of wheel.
m Attention! Always wear safety goggles.
m Attention!
If the grinding wheel or the grinding/sanding belt be-
comes jammed during operation, please remove the
workpiece until the tool reaches its top speed again.

9. Cleaning and maintenance

Always pull out the mains power plug before starting
any cleaning work.
Cleaning
• Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
• We recommend that you clean the device immedi-
ately each time you have finished using it.
• Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep into
the device.
Maintenance
There are no parts inside the equipment which re-
quire additional maintenance.
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the follow-
ing parts are therefore also required for use as con-
sumables.
Wear parts*: grinding medium, carbon brushes,
sharpening wheel, angle gauge, v-belt
* Not necessarily included in the scope of delivery!

10. Storage/Transport

Store the equipment and accessories out of children's
reach in a dark and dry place at above freezing tem-
perature. The ideal storage temperature is between 5
and 30 °C. Store the electric tool in its original pack-
aging.
m Attention! Unplug the machine!
The appliance must unconditionally be secured
against falling or turning down during transport.
The appliance can be lifted on the left and right grind-
ing wheel / belt sander cover.