Technical Data; Unpacking; Assembly - Scheppach 5901320915 Originalbetriebsanleitung

7. Technical data

AC motor
Power consumption
Operating mode
Idle speed
Carbide saw blade
Thickness of saw blade
disc
Number of teeth (pre-
mounted saw blade)
Riving knife thickness
Min. size of workpiece
W x L x H
Min. table size
Max. table size
Cutting height max. 45°
Cutting height max. 0°
Tilting saw blade
Extraction connection
Weight
Technical changes reserved!
*S1:Continuous operation with constant load
Noise
The noise values have been determined in accord-
ance with EN 62841.
Sound pressure level L .............................. 94 dB(A)
pA
Uncertainty K .................................................... 3 dB
pA
Sound power level L .................................107 dB(A)
WA
Uncertainty K ................................................... 3 dB
WA
m WARNING
Excessive and frequent exposure to noise can lead to
hearing damage or hearing loss.
- Wear hearing protection.
- Take breaks.
Total vibration values (vector sum of three directions)
determined according to EN 62841.
NOTE: The specified noise emission values have
been measured in accordance with a standardised
test procedure and can be used to compare one power
tool with another.
The specified noise emission values can also be
used for an initial estimation of the exposure.
WARNING: The noise emission values can vary
from the specified values during the actual use
of the power tool, depending on the type and the
manner in which the power tool is used, and in
particular the type of workpiece being processed.
36 | GB
 www.scheppach.com /  service@scheppach.com /  +800 4002 4002
220 - 240 V~
2000 W
S1
4500 min
1
255 x 30 x 2,8 mm
1,8 mm
24
1,8 mm
10 x 50 x 1 mm
742 x 640 mm
1195 x 640 mm
58 mm
83 mm
0 - 45°
Ø 35 mm
approx. 29 kg
Implement measures to protect against noise nui-
sance.
In doing so, take into account the complete working
process, including the times when the power tool is
working without load or switched off.
Suitable measures include regular maintenance and
care of the power tool and the insertion tools, regu-
lar breaks as well as proper planning of the working
process.
It is necessary to define safety measures to protect
the operator which are based on an estimate of vibra-
tion exposure during the actual operating conditions
(for this, all parts of the operating cycle have to be
considered, e.g. times during which the power tool is
switched off and times during which it is switched on
but runs in no-load mode).

8. Unpacking

m DANGER
Danger of choking or suffocating
The packaging material, packaging and transport
safety devices are not children's toys. Plastic bags,
foils and small parts can be swallowed and lead to
choking.
- Keep packaging material, packaging and trans-
port safety devices away from children.
• Open the packaging and carefully remove the prod-
uct.
• Remove the packaging material, packaging and
transport safety devices (if applicable).
• Check the completeness of the scope of delivery. The
customer service must be notified immediately of any
complaints. Later claims will not be recognised.
• Check the scope of delivery for transport damage.
The transport company must be notified immedi-
ately of any complaints. Later claims will not be
recognised.
• Keep the packaging until the end of the warranty
period.
• Read through the operating manual completely.
• Only use original spare parts or accessories. Orig-
inal spare parts or accessories can be obtained
from your dealer.
• Check that the data on the type plate matches with
the mains power data.

9. Assembly

m WARNING: Remove the mains plug before main-
taining, modifying or assembling the circular table saw.
m Attention!
Always make sure the device is fully assembled
before commissioning!