Operation - REMS Tornado 2000 Betriebsanleitung

g
REMS Sanitol thread-cutting material is mineral oil-free, synthetic, completely
water-soluble and has the lubricating property of mineral oil. It can be used for
all pipe and bolt threads. It must be used for drinking water pipes in Germany,
Austria and Switzerland and complies with regulations (DVGW Test No.
DW-0201AS2032; ÖVGW Test No. W 1.303; SVGW Test No. 7808-649).
Observe the national regulations.
NOTICE
All thread cutting materials may only be used in undiluted form!
2.5. Material Support
CAUTION
Pipes and bars longer han 2 m must be supported additionally by at least one
height-adjustable REMS Herkules 3B material rest. This has steel balls for easy
movement of the pipes and bars in all directions without the material support
tipping over.
2.6. REMS 4" Automatic Die Head
2.7. Subframe, mobile and folding (accessory)
CAUTION
mounted thread cutting machine after releasing. Therefore hold down the
subframe by the handle when releasing and hold with both handles when
moving up.
The mobile, folding subframe is only approved for REMS Tornado and for REMS
the subframe with one hand on the handle, put one foot on the cross member
and release both locking pins by turning the lever. Then hold the subframe with
both hands and move to working height until the two locking pins snap in.
Proceed in he reverse order to fold up. Drain the thread-cutting material from
the oil tray or remove the oil tray before unfolding or folding up.

3. Operation

Use eye protection
3.1. Tools
The die head (8, Tornado / 12, Magnum) is respectively a universal die head,
i.e. for the above mentioned ranges, divided into 2 tool sets, only one die head
Magnum) with the closing and opening lever (10, Tornado / 14, Magnum) must
be in the same direction. The die head then opens automatically on reaching
the respective standard thread length. The length stop (9, Tornado / 13, Magnum)
is folded away to be able to cut cylindrical long threads and bolt threads.
Changing the dies
The dies can be inserted or changed both with mounted and removed die head
(e.g. on the workbench). Release the clamping lever (11, Tornado / 15, Magnum)
to do this, do not unscrew. Push the adjusting disc (12, Tornado / 16, Magnum)
on the handle away from he clamping lever into the end position. The dies are
on the rear of the dies corresponds to the thread size to be cut. Also make sure
holder (14, Tornado / 17, Magnum).
Push the dies into the die head until the ball in the slit of the die holder snaps
in. When all dies are inserted, the desired thread size is set by moving the
the clamping lever. Close he cutting head. Press the closing and opening lever
opens either automatically (for tapered pipe threads) or at any time manually
by exerting slight pressure on the left of the closing and opening lever.
If he holding force of the clamping lever (11, Tornado / 15, Magnum) is not
(e.g. blunt dies), i.e. the die head opens under cutting pressure, the cylinder
head screw on the side opposite the clamping lever (11, Tornado / 15, Magnum)
must be tightened additionally.
pipes.
rear, depending on the length of the pipe.
3.2. Chuck
3.2.1. Chuck Tornado (19)
The self-centring dies open and close automa ically by turning the switch to
the left or right (18) and actuating the foot switch (21). When changing the front
and rear dies, please make sure that the individual dies are inserted as shown
in Fig. 4 and 5 because otherwise damage will be caused. The machine may
Use ear protection
3.2.2. Quick Action Hammer Chuck (1), Guide Chuck (2) Magnum
inserted into the die carriers ensures centred and safe clamping with the least
force. As soon as the material protrudes from the guide chuck, this must be
closed.
To change the dies (24), close the clamping ring (22) up to approx. 30 mm
clamping diameter. Remove screws of the dies (24). Push out the dies to the
back with a suitable tool (screwdriver). Push the new dies with inserted screw
into the die carriers from the front.
3.3. Work Procedure
Remove blockages of chips and fragments of the workpiece before starting
work.
NOTICE
Switch off the thread cutting machine when the tool set approaches he machine
housing.
3.3.1. Tornado
Swing out tools and move the tool carrier to the right end position with the
pressing lever (5). Insert the material so that it protrudes approx. 10 cm from
the chuck (19). Swing down and close the dies head (8). Switch the switch (18)
to position 1, actuate the foot switch (21). Now the material is clamped auto-
matically.
CAUTION
Never reach into the revolving clamping or guide chuck. There is a risk of
injury.
With types 2010 and 2020 the 2nd speed can be selected for cutting off and
deburring and for cutting smaller threads. Switch the switch (18) rapidly from
position 1 to position 2 with the machine running to do this. Press the die head
against the rotating material with the pressing lever (5). After one or two thread
turns the die head continues to cut automatically. The die head opens auto-
matically on reaching the standard thread length for tapered pipe threads. For
long threads and bolt threads, open the die head manually with the machine
running by pressing the closing and opening lever (10) on the left. Release the
material is released.
Unlimitedly long threads can be cut by re-tightening the material. To do this,
release the foot switch (21) when the tool carrier (2) approaches the machine
housing during thread cut ing. Do not open the die head. Set switch (18) to R.
Release the material, move the tool carrier and material to the right end posi ion
with the pressing lever. Switch the machine back on in switch position 1.
To cut pipes, the pipe cutter (15) is swung in and pushed to the desired cutting
position using the pressing lever (5). The rotating pipe is cut by turning the
spindle to the right. The inside burr created by cutting is removed with the pipe
inside deburrer (16).
Draining thread-cutting material in REMS Tornado 2000, 2010, 2020: Pull off
the hose from the tool carrier (2) and hold into the container. Let he machine
run until he oil tray is empty. or: Remove he oil tray and empty via he spout (17).
Draining thread-cutting material in REMS Tornado 2000 T, 2010 T, 2020 T: Pull
off he hose from the tool carrier (2) and hold into the container. Let the machine
run until the oil tray is empty. or: Remove the stopper (25) and drain the oil tray.
3.3.2. Magnum
Swing out tools and move the tool carrier to the right end position with the
pressing lever (8). Insert the material through the opened guide chuck (2) and
until the dies are touching the material. With the clamping ring tighten the
material once or twice after a brief opening movement. The material protruding
to the rear is centred by closing the guide chuck (2). Swing down and close the
die head. Switch the switch (3) to 1, actuate the foot switch (4). Magnum 2000 /
3000 / 4000 is only switched on and off with the foot switch (4), switch (3) is
not provided.
In Magnum 2010 / 3010 / 4010 and 2020 / 3020 / 4020 the second speed can
be selected for cutting off and deburring and for cutting smaller threads. Switch
the switch (3) rapidly from position 1 to position 2 with he machine running to
do this. Press the die head against the rotating material with the pressing lever
(8). After one or two thread turns the die head continues to cut automatically.
The die head opens automatically on reaching the standard thread length for
tapered pipe threads. For long threads and bolt threads, open the die head
manually with the machine running by pressing the closing and opening lever
chuck, remove material.
Unlimitedly long threads can be cut by re-tightening the material. To do this,
release the foot switch (4) when the tool carrier approaches the machine housing
during thread cutting. Do not open the die head. Release the material, move
the tool carrier and material to the right end position with the pressing lever.
Clamp the material again, switch the machine back on. To cut pipes, the pipe
cutter (18) is swung in and pushed to the desired cutting position using the
pressing lever. The rotating pipe is cut by turning the spindle to the right. The
inside burr created by cutting is removed with the pipe inside deburrer (19).
Drain thread-cutting material. Pull off the hose from the tool carrier (7) and hold
into the container. Let the machine run until the oil tray is empty. or: Remove
the stopper (25) and drain the oil tray.
g