Configuration Of The Charger; Preparation Of The Machine; Charging The Battery; Assembly And Removal Of The Brush - Sprintus Torana Bedienungsanleitung

• Lift out the waste water tank. (Photo B-17) Discon-
nect the Anderson connector of the battery cable from
the Anderson connector of the machine cable. Do not
pull the plug out of the socket by the cable.
• Connect the battery terminals to the battery
terminal marked with the same symbol. (red
cable "+", black cable "-")! A possible short cir-
cuit of the battery can lead to explosions!
Make sure all controls are set to "0" or "Off". Now the
battery connector (18) can be reconnected.
• Close the battery compartment, taking care not
to squeeze any cable.
6.3

CONFIGURATION OF THE CHARGER

This procedure must be performed by trained tech-
nicians. When purchasing the scrubber-dryer, the
built-in battery charger is configured for operation
with GEL batteries.
6.4

PREPARATION OF THE MACHINE

• Before starting work, wear non-slip shoes, gloves
and any other personal protective equipment speci-
fied by the manufacturer for the cleaning agents or
required by the working environment.
☞ Before starting work, the following operations must
be carried out. For a detailed description of these
phases, refer to the corresponding sections in the
operating instructions: Check the battery charge and
charge the battery if necessary.
Install the brushes or the pad drive plate (with corre-
sponding pads) suitable for the surface to be treated.
Assemble the squeegee and check that it is well fas-
tened and connected to the suction hose. Check the
rubber lips for wear and make sure the waste water
tank is empty.
Fill the fresh water tank with a water / cleaning agent
solution with the prescribed mixing ratio. Only use
non-foaming cleaning agents.
☞ to avoid danger, familiarise yourself with the ma-
chine on a large, obstacle-free surface.
For best results with regard to cleaning and service
life of the appliance, please note the following instruc-
tions:
Review the work area and remove any obstacles. If
the area to be cleaned is very large, it should be sub-
divided into contiguous rectangular areas parallel to
each other.
- Choose a straight working track and start working in
the back of the room so that you do not have to run
over areas that have already been cleaned.
7 OPERATION
7.1

CHARGING THE BATTERY

Prepare and check the battery charger as described.
• Follow the instructions in the battery manufactur-
er's user and safety manual.
7.2 ASSEMBLY AND REMOVAL OF THE
BRUSH
• Always make sure the brushes or the pad drive
plate are properly installed.
Assembly:
Place the brush on the floor; Lift the squeege with
the lever (photo B-19). Push the handlebar down-
wards (photo A-1) and lift the front part of the ma-
chine so that the machine is standing on the rear
roller (photo C-20). Position the machine over the
brush so that the mounting flange of the brush
is under the bayonet coupling of the drive shaft.
Turn the machine on (Photo E-32) with the main
switch on the control panel (Photo E-13). Press the
pushbutton "Smart Run" (E-33) to select operation
of the brush and suction. Start operation with the
(Photo A-2). The brush / pad drive plate automati-
cally engages.
• The minimum length of the bristles is 1 cm.
• The minimum thickness of the pads is 1 cm.
Overly worn brushes or overly thin pads can dam-
age the machine and the floor. Check the wear con-
dition of the accessory before starting work.
Brush / pad drive plate drop:
Ensure that both the motor of the brush and the
suction motor are switched off (corresponding in-
dicator lights must be off).
Lift off the squeegee (photo B-19).
Push the handlebar downwards (photo A-1) and
lift the front part of the machine so that the ma-
chine is standing on the rear roller (photo C-20).
Press switch (A-2) and the pushbutton (E-35) at
the same time.
This automatically drops the brush.
7.3 SWITCHING OFF/TRANSPORT OF
THE MACHINE
To turn off the machine at standstill, Proceed as
follows:
Switch off the machine (photo E-32) at the main
switch of the control panel (photo E-13). Lift the
squeegee using the lever (photo B-19) and remove
the brush. Push the handlebar downwards (photo
A-1) and lift the front part of the machine so that
the machine is standing on the rear roller (photo
C-20).
Only transport the machine when switched off.
Turn off the device on the control panel (photo
E-13) by pressing the ON/OFF switch (photo E-32).
Lift off the suction bar (photo B-19). Hold the han-
dlebars tightly and push it down to the support
wheel (photo C-20).
The machine lifts at the front.
Hold the machine in position and slide it to the
desired position.
27