Scheppach 5901318901 Originalbetriebsanleitung Seite 39

11.1.2 Overload protection
In the event of overloading, the motor will switch itself
off. After a cool-down period (time varies) the motor
can be switched back on again.
1. Allow the product to cool.
2. Press the overload switch (13).
3. Switch on the machine as described in 11.1.1.
11.2 Setting the cutting depth (fig. 1)
The saw blade (7) can be adjusted to the required cut-
ting depth by turning the crank wheel (15).
• Counterclockwise: Greater cutting depth
• Clockwise: Smaller cutting depth
Check the setting with a test cut.
11.3 Setting the cutting angle (fig. 1)
With the circular table saw, angled cuts from 0 ° to
45 ° to the left of the parallel stop (1) can be carried
out.
m Before each cut, check that no collision can occur
between the parallel stop (1), the transverse stop (9)
and the saw blade (7).
1. Loosen the locking lever (14).
2. Set the desired angle on the scale (16) by simulta-
neously pushing in and turning the crank wheel (15).
3. Lock the locking lever (14) at the desired angle
setting.
11.4 Using the parallel stop
11.4.1 Stop heights (fig. 16)
• The stop rail (1a) of the parallel stop (1) has two
guide surfaces at different heights.
• Depending on the thickness of the material to be
cut, the stop rail (1a) must be used for thick materi-
al (workpiece thickness exceeding 25 mm) and for
thin material (workpiece thickness below 25 mm).
11.4.2 Setting the stop rail (fig. 16)
1. To move the stop rail (1a) to the lower guide sur-
face, loosen the two wing nuts (1b) to release the
stop rail (1a) from the parallel stop (1).
2. Pull out the stop rail (1a) along the groove.
3. Turn the stop rail (1a) and slide the sliding block
along the second groove.
4. Tighten the wing nuts again (1b).
5. Shifting to the higher guide surface must be car-
ried out in the same way.
11.4.3 Changing the side of the parallel stop (fig. 16)
1. Fully unscrew the wing nuts (1b).
2. Remove the stop rail (1a) and insert the coach bolts
(1c) on the opposite side of the parallel stop (1).
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
11.4.4 Setting the cutting width (fig. 11)
• The parallel stop (1) must be used when cutting
sections of wood lengthways.
• The parallel stop (1) can be mounted on both sides
of the saw table (2).
• Two scales are printed on the guide rail (28) on the
front side of the saw table (2). One written in red
and another one in black indicating the distance
between stop rail (1a) and saw blade (7) (cutting
width):
- Use the upper scale in black, if you have mount-
ed the stop rail (1a) flat (for thin material).
- Use the lower scale in red, if you have mounted
the stop rail (1a) upright (for thick material).
To set the parallel stop (1) to the desired dimension,
proceed as follows:
1. Raise the eccentric lever (E).
2. Slide the parallel stop (1) until you see the desired
dimension on the scale of the guide rail (28) in the
sight glass (29).
3. To fix it in place, press the eccentric lever (E) fully
downwards.
11.4.5 Setting the stop length (fig. 17)
To avoid the material to be cut becoming jammed, the
stop rail (1a) can slide in a longitudinal direction.
Rule of thumb: The rear edge of the stop should inter-
sect an imaginary line that starts roughly at the centre
of the saw blade and runs to the rear at 45 °.
1. Set the required cutting width.
2. Undo the wing nuts (1b).
3. Slide the stop rail (1a) far enough forward that it
touches the imaginary 45 ° line.
4. Tighten the wing nuts (1b) again.
11.4.6 Adjusting the parallel stop (fig. 18)
If the parallel stop (1) including stop rail (1a) is not
parallel to the saw blade (7), it must be readjusted.
Proceed as follows:
1. Remove the saw blade guard (8).
2. Set the saw blade (7) to the maximum cutting
depth.
3. Position the parallel stop (1) such that the stop rail
(1a) makes contact with the saw blade (7).
PREREQUISITE: The stop rail (1a) has already
been set to the lower guide surface (see 11.4.2).
4. If the stop rail (1a) is not in line with the saw blade
(7), loosen the Phillips screws (1d) in the parallel
stop (1) with an Phillips screwdriver and align the
stop rail (1a) parallel to the saw blade (7).
5. Tighten the Phillips screws (1d) again.
6. Again, position the parallel stop (1) away from the
saw blade (7).
GB | 39