Residual Risks; Technical Data; Before Starting The Equipment - Scheppach TS82 Originalbetriebsanleitung

• Refitting, including adjusting and measuring
works, and cleaning must be carried out only
when the motor is switched off. - Disconnect
the main power plug -
• Before switching on again, ensure that keys and
adjustment tools have been removed.
Warning! This electric tool generates an electromag-
netic field during operation. This field can impair active
or passive medical implants under certain conditions.
In order to prevent the risk of serious or deadly inju-
ries, we recommend that persons with medical implants
consult with their physician and the manufacturer of
the medical implant prior to operating the electric tool.
Safety Instructions for the Handling of Saw Blades
Only use insertion tools if you have mastered their
1
use.
2 Observe the maximum speed. The maximum speed
specified on the insertion tool may not be exceeded.
If specified, observe the speed range.
3 Observe the motor / saw blade direction of rotation.
4 Do not use any insertion tools with cracks. Sort out
cracked insertion tools. Repairs are not permitted.
5 Clean grease, oil and water off of the clamping sur-
faces.
Do not use any loose reducing rings or bushes for
6
the reducing of holes on saw blades.
7 Make sure that fixed reducer rings for securing the
insertion tool have the same diameter and have at
least 1/3 of the cutting diameter.
Make sure that fixed reducer rings are parallel to
8
each other.
Handle insertion tool with caution. They are ideally
9
stored in the originally package or special containers.
Wear protective gloves in order to improve grip and
to further reduce the risk of injury.
10 Prior to the use of insertion tools, make sure that all
protective devices are properly fastened.
11 Prior to use, make sure that the insertion tool meets
the technical requirements of this electric tool and is
properly fastened.
12 Only use the supplied saw blade for sawing opera-
tions in wood, materials similar to wood, plastics and
non-ferrous metals (except for magnesium and alloys
containing magnesium).

Residual risks

The machine has been built according to the state of
the art and the recognised technical safety require-
ments. However, individual residual risks can arise
during operation.
• Health hazard due to electrical power, with the use of
improper electrical connection cables.
• Furthermore, despite all precautions having been met,
some non-obvious residual risks may still remain.
• Residual risks can be minimised if the „safety instruc-
tions" and the „Proper use" are observed along with
the whole of the operating instructions.
• Do not load the machine unnecessarily: excessive
pressure when sawing will quickly damage the saw
blade, which results in reduced output of the machine
in the processing and in cut precision.
• Avoid accidental starting of the machine: the oper-
ating button may not be pressed when inserting the
plug in an outlet.
• Use the tool that is recommended in this manual. In
doing so, your saw provides optimal performance.
• Hands may never enter the processing zone when the
machine is in operation. Release the handle button
26 І 48
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
and switch off the machine prior to any operations.
Prior to any adjustment, maintenance or service work dis-
connect the mains power plug!

Technical Data

AC motor
performance
operating mode
Idle speed
Hard-metal blade
Number of teeth
Thickness riving knife
table size
Cutting height max. 90°
Cutting height max. 45°
height adjustment
saw blade swivel
suction port
weight
Noise values
The total noise values determined in accordance with
EN 61029.
sound pressure level L
pA
uncertainty K
pA
sound power level L
WA
uncertainty K
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing. Total
vibration values (vector sum - three directions) deter-
mined in accordance with EN

Before starting the equipment

• All covers and safety devices have to be properly fitted
before the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails or
screws, etc.
• Before you press the ON/OFF switch check that the
saw blade is fitted correctly. Moving parts must run
smoothly.
• Before you connect the equipment to the power supply
make sure the data on the rating plate are dentical to
the mains data.
• Connect the machine to a properly installed protec-
tive contact socket, with at least 16A circuit breaker.
230 V~ 50Hz
1100 Watt
S1
4750 min
-1
ø 270 x ø 30 x 2,7 mm
18
2,3 mm
540x400 mm
60 mm
40 mm
0 - 60 mm
0 - 45°
ø 100 mm
75 kg
86,5 dB(A)
3 dB
95,7 dB(A)
3 dB
61029.