Specifications; Operation - Kärcher CB 1/23 Eco Bedienungsanleitung

Bleed dosing pump
 Turn bleeder screw (c) ca. 2 rotations
anti-clockwise.
 Press button (b) so often until there are
no more air bubbles in the suction hose
and the detergents and drying aid flows
back via run-off hose into the container.
 Screw close the bleeder screw (c)
again.

Specifications

Dimensions
Plant dimensions
CB 1/
23
Eco
Height mm 3150 3350 3650
Width mm
Depth *) mm
Vehicle size limits dimensions **)
Washing mm
width
Washing mm 2300 2500 2800
height
Washable vehicle lengths ***)
without safe- mm
ty distance
with safety mm
distance
Hall width
with safety mm
distance
without safe- mm
ty distance
*) rotating roof brush, rotating side-brushes
**)almost all the vehicles can be washed
within these dimensions
***) For driving track length of 9000 mm
Features
Wash brushes
Diameter of side-brushes
Side
Side-brush rotation
speed
Diameter of brush Roof
Brush rotation speed
Roof
Portal drive speed
Sound level
Brush cleaning
Drier operation
24
Electrical connection
Voltage
Frequency
Connection output Ba-
sic plant
Pre-securing Control
cabinet
Water connection
Nominal width
Flow pressure accord-
ing to DIN 1988 (with
CB 1/ CB 1/
100 l/min)
25 28
Temperature
Eco Eco
Water consumption/ve-
hicle with 0.45 MPa
3500
(programme-depend-
2020
ent with 4.5 m vehicle
length)
2300
Compressed air connection
Nominal width
Pressure
Consumption/Washes
5800
(without anti-frost de-
vice, programme-de-
pendent with 4.5 m
5270
vehicle length)
4500
In the event of danger for persons, property
and animals, the plant must be switched off
4050
immediately by pressing the emergency-
stop button. It is found
at the wash card/code reader
–
at the operating place for manual oper-
–
ator station
at the entrance to the wash hall, íf an
–
operating point or wash card/code
reader is located there.
Warning!
mm 965
Risk of damage to vehicle which is to be
cleaned. If the wash plant develops a fault
1/min 107
once the detergent has been applied, it
must be switched off and the detergent re-
moved by spraying the vehicle thoroughly
mm 880
with water to prevent the paintwork being
1/min 127
damaged through an extended period of
exposure to the detergent.
m/min 0...20
Warning
When using Carlite brushes, the vehicle
dB(A) 67
must be manually cleaned beforehand, if
dB(A) 87
the appliance is not equipped with an up-
grade kit high pressure!
Note
In the case of self-operating plants, a spe-
cialist familiar with the plant must be con-
tactable who can carry out measures, or
have them done, in order to avoid possible
dangers.
Connection values
V 400/3~, P,
Hz
kW approx. 10
A max. 35
Inch
MPa 0,4...0,6
(bar) (4...6)
°C max. 50
l 80...210
Inch
MPa 0,6...0,8
(bar) (6...8)
l

Operation

5
-
EN
Switching on after emergency-stop
Note
Before switching on again, the cause for
activating the emergency switch button has
N
to be remedied. Persons or animals may
50
not remain in the working area. Vehicles
must be driven out of the plant.
1
1 Emergency-stop button
2 Control supply voltage/normal position
button
3 Start key
 Pull all emergency-stop buttons to un-
1/2
lock them.
 Set automatic/manual switch at the
feeder to automatic.
 Press control supply voltage/normal po-
200
sition button on the operating point for
manual mode.
The plant is again ready for operation and the
the vehicle being washed can be driven in.
Start up
 Stop valve opens for water and com-
pressed air.
 Set main switch on the feeder to "1".
 Set automatic/manual switch to auto-
matic.
 Press control supply voltage/normal po-
sition button on the operating point for
manual mode.
The plant is again ready for operation and the
the vehicle being washed can be driven in.
Preparing the vehicle
Warning
In order to avoid damage to the vehicle, the
following precautionary measures have to
taken on the vehicle before starting the
wash plant:
 Close windows, doors and roof space..
 Push in antennas, fold over in direction
of rear or dismantle.
 Fold in large or wide overhanging mirrors.
 Check vehicle for loose vehicle parts
and dismantle them, e.g.:
chrome strips,
–
spoilers,
–
bumpers,
–
door handles,
–
exhaust pipes,
–
wind-breakers,
–
tilt ropes,
–
sealers,
–
anti –dazzle visors attached on the ve-
–
hicle,
racks.
–