Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operation
1.
Use the product only in daylight or good
artificial light.
2.
Never operate the product with damaged
guards or shields or without guards or shields
in place.
3.
Keep hands and feet away from the cutting
device at all times and especially when
switching on the motor.
4.
Before using the product and after any
impact, check for signs of wear or damage
and repair as necessary.
5.
Always disconnect the product from the
power supply (i.e. remove the plug from the
power supply or the battery pack)
whenever leaving the product unattended;
¢
adjusting the working position of the cutting
¢
device;
before clearing a blockage;
¢
before checking, cleaning or working on
¢
the product
after striking a foreign object;
¢
whenever the product starts vibrating
¢
abnormally.
6.
Ensure that the product is correctly located in
a designated working position before starting
the motor.
7.
While operating the product, always ensure
that the operating position is safe and secure,
especially when using steps or a ladder.
8.
Do not operate the product with a damaged
or excessively worn cutting device.
9.
Always ensure that all handles and guards
are fitted when using the product. Never
attempt to use an incomplete product or one
fitted with an unauthorised modification.
10. Always use two hands to operate a product
fitted with two handles.
11. Always be aware of your surroundings and
stay alert for possible hazards of which you
may not be aware due to the noise of the
product.
12. Take care against injury to feet and hands
from the cutting device.
13. Always ensure that the air vents are kept clear
of debris.
14. Wear slip-resistant foot protection and
protective clothing when using this product.
15. Always keep proper footing and operate
the product only when standing on a fixed,
secure and level surface. Change working
positions regularly to avoid tiredness and
ensure a comfortable working position at all
times.
16. Never use replacement parts or accessories
not provided or recommended by the
manufacturer.
17. The use of this product may be restricted due
to national regulations.
Maintenance and storage
1.
Disconnect the product from the power
supply (i. e. remove the plug from the power
supply or the battery pack) before checking,
cleaning or working on the product and when
it is not in use.
2.
Disconnect the product from the power supply
(i.e. remove the plug from the power supply
or the battery pack) before carrying out
maintenance or cleaning work.
3.
Maintain and inspect your product regularly.
Check for misalignment or binding of
moving parts, breakage of parts and any
other condition that may affect the product's
operation. If damaged, have the product
repaired before use. Many accidents are
caused by poorly maintained products.
4.
Improper maintenance will lead to
malfunction/failure of the product.
5.
Inspect the product before each use, after
dropping the product or exposing to other
impacts to identify significant defects. Check
for loose fasteners and damaged parts, such
as cracks in the cutting attachment.
6.
Use only the manufacturer's recommended
replacement parts and accessories.
7.
Inspect and maintain the product regularly.
Have the product repaired only by an
authorised service centre or similar qualified
specialist.
8.
When not in use, store the product out of the
reach of children.
9.
When transporting or storing the product,
always fit the cutting device transport guard
(i. e. blade cover).
Vibration and noise reduction
Q
To reduce the impact of noise and vibration
emission, limit the time of operation, use low-
vibration and low-noise operating modes as well
as wear personal protective equipment.
Take the following points into account to minimise
the vibration and noise exposure risks:
Only use the product as intended by its
¢
design and these instructions.
Ensure that the product is in good condition
¢
and well maintained.
Use correct attachments for the product and
¢
ensure they are in good condition.
GB
11
Werbung
Kapitel
Inhaltsverzeichnis
