Bosch UniversalChain 18 Originalbetriebsanleitung Seite 21

OBJ_BUCH-3472-001.book Page 21 Thursday, December 21, 2017 4:11 PM
Meaning of the Indication Elements (AL 1830 CV)
(Fast) Flashing of the Green Battery Charge
Indicator
The rapid-charging procedure is indicated by
fast flashing of the green battery charge
indicator.
Note: The rapid-charging procedure is only possible when the
battery temperature is within the allowable charging
temperature range, see section "Technical Data".
(Slow) Flashing of the Green Battery Charge
Indicator
When the charging condition of the battery is
80 %, the green battery charge indicator
flashes slowly.
The battery can be removed for immediate use.
Continuous Lighting of the Green Battery Charge
Indicator
Continuous lighting of the green battery
charge indicator indicates that the battery is
fully charged.
When the battery is not inserted, continuous lighting of the
battery charge indicator indicates that the mains plug is
inserted in the socket and that the battery charger is ready for
operation.
Continuous Lighting of the Red Battery Charge
Indicator
Continuous lighting of the red battery charge
indicator indicates that the temperature of the
battery is not within the allowable charging temperature
range, see section "Technical Data". As soon as the allowable
charging temperature range is reached, the battery charger
automatically switches to rapid charging.
Flashing Red Battery Charge Indicator
A flashing red battery charge indicator
indicates a different malfunction of the
charging procedure, see section "Troubleshooting – Causes
and Corrective Measures".
Troubleshooting – Causes and Corrective
Measures
Cause Corrective Measure
Continuous lighting of the battery charge indicator
Flashing red battery charge indicator
No charging procedure possible
The battery is not attached Attach battery to charger
(correctly) correctly
Battery contacts Clean the battery contacts
contaminated (e.g. by inserting and
removing the battery several
times) or replace the battery
Battery pack defective Replace the battery
Bosch Power Tools
Cause Corrective Measure
Battery charge indicators do not light up
Mains plug of battery Insert mains plug (fully) into
charger not plugged in the socket outlet
(properly)
Socket outlet, mains cable Check the mains voltage;
or battery charger defective have the battery charger
checked by an authorised
after-sales service agent for
Bosch power tools
Charging Advice
With continuous or several repetitive charging cycles without
interruption, the charger can warm up. This does not indicate
a technical defect of the battery charger.
A significantly reduced working period after charging
indicates that the battery is used and must be replaced.
Battery Charge-control Indication
The battery charge-control indicator on the power tool
consists of three green LEDs. It indicates the charging
condition of the battery for a few seconds after the tool is
switched on and off.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Slow flashing 1 x green
Mounting and Tensioning the Chain
Saw
 Do not insert battery before the chain saw is
completely assembled.
 Always wear protective gloves when handling the
chain.
Chain and Chain Bar Assembly
(see figures B1–B4)
 Use only chains with a drive link thickness of 1,1 mm.
– Unpack all parts carefully.
– Place the chain saw on any suitable flat surface.
– Insert the saw chain 12 in the slot around the chain bar 11.
Observe the correct running direction by comparing the
saw chain to the rotation symbol.
– Place the chain links around the drive sprocket 20 and
mount the chain bar 11.
– Check if all parts are seated properly and hold the chain
bar and the chain in this position.
– Remount the cover 15.
– Lightly tighten the cover 15 with the clamping knob 14.
– The chain is not yet tensioned. The saw chain is tensioned
as described in section "Tensioning the Saw Chain".
English | 21
Capacity
≥ 66%
33—66%
11—33%
≤ 10%
F 016 L81 719 | (21.12.17)