Standard Accessories; Optional Accessories; Battery Rem Oval/ Installation - Hitachi WH 12DAF2 Bedienungsanleitung

CHARGER
M odel
Charging tim e
Charging voltage
Weight
" ×" Indicates that the battery pack is not com patible w ith that specific charger.
NOTE: The charging tim e m ay vary according to the am bient tem perature and pow er source voltage.

STANDARD ACCESSORIES

1. Charger (UC14YFA or UC18YG) ............................... 1
2. Plastic case ................................................................ 1
Standard accessories are subject to change w ithout
notice.

OPTIONAL ACCESSORIES

(Sold separately)
1. Battery (EB1214S, EB1220BL, EB1226HL)
2. For WH12DAF2
There are tw o types of attachm ent sizes for the driver
bit and the socket. Please refer to the table below and
select the attachm ent size for the driver bit or socket
that is appropriate for your WH12DAF2.
Attachm ent size
17m m
Type-L
12m m
Type-S
3. For WR12DAF2
Th e W R12DA F2 t y p e i s a 12.7 sq u ar e d r i v er
specification. Please select the socket w ith the
appropriate attachm ent size.
Optional accessories are subject to change without notice.
UC14YFA
EB1214S: Approx. 30 m in. (at 20° C)
EB1220BL: Approx. 50 m in. (at 20° C)
EB1226HL: Approx. 60 m in. (at 20° C)
7.2 – 14.4 V
0.6 kg
Purchase location
Republic of Korea,
13m m Taiwan, Hong Kong,
People's Republic of
China, Republic of
Singapore
9m m
Other than above
regions.
EB1214S: Approx. 30 m in. (at 20° C)
EB1220BL: Approx. 50 m in. (at 20° C)
APPLICATION
〈WH12DAF2〉
Driving and rem oving of sm all screw s, sm all bolts,
etc.
〈WR12DAF2〉
Tightening and loosening of all types of bolts and
nuts, used for securing structural item s

BATTERY REM OVAL/ INSTALLATION

1. Battery removal
Hold the handle tightly and push the battery latch to
rem ove the battery. (See Fig. 1 and 2)
CAUTION:
Never short-circuit the battery.
2. Battery installation
Insert the battery w hile observing its polarities. (See
Fig. 2)
CHARGING
〈UC14YFA〉
Before using the power tool, charge the battery as follows.
1. Connect the charger's pow er cord to a receptacle
When the pow er cord is connected, the charger's
pilot lam p w ill blink in red. (At 1-second intervals.)
2. Insert the battery into the charger
Insert the battery firm ly, in the direction show n in
Fig. 3, until it contacts the bottom of the charger
com partm ent.
CAUTION:
If the battery is inserted in the reverse direction, not
only recharging w ill becom e im possible, but it m ay
also cause problem s in the charger such as deform ed
recharging term inal.
3. Charging
When inserting a battery in the charger, charging w ill
co m m en ce an d t h e p i l o t l am p w i l l l i g h t u p
continuously in red.
When the battery becom es fully recharged, the pilot
lam p w ill blink in red. (At 1-second intervals.) (See
Table 1)
(1) Pilot lam p indication
The indications of the pilot lam p w ill be as show n in
Table 1, according to the condition of the charger or
the rechargeable battery.
English
UC18YG
×
7.2 – 18 V
0.3 kg
8