Safety Notes - Scheppach 1901501901 Originalbetriebsanleitung

10. Adjustment handle for upper blade wheel
11. Motor
12. Suction connector
13. Adjustment handle for saw blade safety device
Noise parameters according to EN 3744.
Sound level in dB
according to EN 61029-1, En 61029-2-5; 13.2
Operation L = 87.0 dB(A)
WA
Sound level at the workplace in dB
Operation L = 77.0 dB(A)
pAeq
A measurement uncertainty allowance K = 3 dB applies
to the mentioned emission values.
m
In these operating instructions we have
marked the places that have to do with your
safety with this sign.
m

Safety notes

• Please pass on safety notes and instructions to all
those who work on this machine.
• Personnel entrusted with work on the machine must
have read the operating instructions and in particular
the chapter on safety before beginning work. Reading
the instructions after work has begun, is too late. This
applies especially to persons working only occasionally
on the rnachine, e.g. during setting up or rnaintenance.
• Observe all safety instructions and warnings attached
to the machine.
• See to it that all safty instructions and warnings attached
to the machine are complete and perfectly legible.
• Check all power supply lines. Do not use defective
lines.
• Make sure that the machine stands stable on firm
ground.
• Insure sufficient lighting in the work area and the area
around the machine.
• Caution when working: There is a danger to fingers
and hands from the rotating tool.
• During the operation of the machine all safety devices
and covers must be mounted, and the door protecting
the saw blade must be closed.
• Keep away other persons, in particular children, from
your working area and the machine connected to the
mains as well as from the supply lines.
• Make sure that children cannot access the machine
while it is not in use.
• Do not overload the device and use it only within the
performance range according to the technical specifi-
cations contained in the operating instructions.
• If you work with the machine outside, make sure it is
in an upright position, and wear shoes with an anti-slip
sole.
• Do not use the cable for other purposes than it is in-
tended for. Protect it from heat, oil, and sharp edges.
• Only use well-sharpened saw blades to make your
work more effective and safe.
• Make sure the handles are dry, clean, and free from oil
and grease.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
• Make sure that wrenches and adjustment tools have
been removed before you turn the machine on.
• If you use the machine outside, only use approved ex-
tension cables that are identified accordingly.
• Keep away other persons, in particular children, from
your working area and the machine connected to the
mains as well as from the supply lines.
• Be careful and always pay attention to what you are
doing. Perform your work sensibly. Do not use the de-
vice when you cannot concentrate.
• When working on the machine, all safety mechanisms
and covers must be mounted.
• Keep children away from the machine when it is con-
nected to the power supply.
• Always keep the operator's place clean, remove chips
and waste wood. Disorder in the working area may re-
sult in accidents.
• Protect the device from rain and humidity.
• Do not use the machine in humid or wet environments.
• Store the machine at a safe place to ensure that per-
sons may not injure themselves at the standing ma-
chine or may put the machine into operation. Please
make sure that the machine is not standing outside
without any protection or is in a humid environment.
• Only use the machine according to the intended use.
• Do not use the device if there is a risk of fire or explo-
sion.
• Make sure your body does not come into contact with
grounded parts (e.g. tubes, radiators, electric kitchen
ranges, cooling devices) while you work with the de-
vice.
• Operating personal must be at least 18 years of age.
Trainees must be at least 16 years of age, but may only
operate the machine under adult supervision.
• Persons working on the machine may be not diverted
from their work.
• The working space on the machine must be free of
chips and wood scrap.
• Wear only close-fitting clothes. Remove rings, brace-
lets and other jewelry.
• Wear an ear protection, safety glasses, as well as a dust
protection mask while you are working with the machine.
• Always wear safety goggles when working.
• Wear a cap or hair net to protect long hair.
• Do not wear work gloves while you use the saw, except
from rough materials.
• Do not wear work gloves when working on the saw.
• Observe the correct rotational speed setting on the
machine.
• The safety mechanism on the machine may not be re-
moved or rendered unusable.
• Cleaning, changing, calibrating, and setting of the
machine may only be carried out when the motor is
switched off. Pull the power supply plug and wait for
the rotating tool to completely stop.
• Connection and repair work on the electrical installa-
tion may be carried out by a qualified electrican only.
• All protection and safety devices must be replaced af-
ter completing repair and maintenance procedures.
• Switch the machine off and pull power supply plug
when rectifying any malfunctions.
15 І 120