Before Starting The Equipment - EINHELL TC-CD 18-2 Li Originalbetriebsanleitung

5. Before starting the equipment

Be sure to read the following information before
you use your cordless screwdriver for the fi rst
time:
1. Charge the battery pack with the charger
supplied. An empty battery pack requires a
charging period of approximately 3 to 5 hours.
2. Only ever use sharp drill bits and screwdriver
bits which are suitable for the purpose and in
faultless condition.
3. Always check for concealed electric cables
and gas and water pipes when drilling and
screwing in walls.
6. Operation
6.1 Charging the Li battery pack (Fig. 2-3)
1. Remove the battery pack (5) from the handle,
pressing the pushlock button (8) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate.
3. Plug the battery charger (6) into the power
socket and connect the charging cable (a) to
the battery (5). The three LEDs on the battery
capacity indicator (10) indicate that the batte-
ry is being charged.
- Battery empty: All three LEDs fl ash alterna-
tely
- 1/3 charged: The LED on the left lights up
and the LEDs in the middle and on the right
fl ash alternately
- 2/3 charged: The LEDs on the left and in
the middle light up and the LED on the right
fl ashes
4. When charging is fi nished after approx. 3-5
hours, all three LEDs light up for approx. 10
minutes. Remove the charger from the batte-
ry.
5. If all three LEDs fl ash at the same time, the
battery temperature is either too low or too
high. Remove the charger from the battery,
keep the battery at room temperature for a
day and try again.
6. If the fault is still indicated, the battery is
defective. Do not use or charge a defective
battery. Remove the charger from the battery.
If the battery pack fails to become charged, ple-
ase check
•
whether there is voltage at the socket-outlet
•
whether there is proper contact at the char-
Anl_TC_CD_18_2_Li_SPK7.indb 17 Anl_TC_CD_18_2_Li_SPK7.indb 17
GB
ging contacts on the charger.
If the battery still fails to become charged, please
return
•
the charger
•
the battery pack
to our Customer Service Department.
To ensure that the LI battery pack provides
long service you should take care to recharge
it promptly. You must recharge the battery pack
when you notice that the power of the cordless
screwdriver drops.
6.2 Torque setting (Fig. 4 / Item 1)
Important! The tool must be at a standstill
when you set the torque with the setting ring.
The cordless screwdriver is fi tted with a mechani-
cal torque selector.
The torque for a specifi c size of screw is selected
with the set-collar (1). The correct torque depends
on several factors:
•
on the type and hardness of material in ques-
tion
•
on the type and length screws used
•
on the requirements needing to be met by the
screwed joint.
The clutch disengages with a grating sound to
indicate when the set torque is reached.
6.3 Drilling (Fig. 4 / Item 1)
For drilling purposes, move the set-collar to the
last step „Drill". In this setting the slip clutch is in-
active. The maximum torque is available in drilling
mode.
6.4 Forward/Reverse switch (Fig. 5 / Item 3)
With the slide switch above the On/Off switch you
can select the direction of rotation of the battery-
powered drill/screwdriver and secure it against
being switched on accidentally. You can choose
between clockwise and anticlockwise rotation. To
avoid causing damage to the gearing it is advisa-
ble to change the direction of rotation only when
the tool is at a standstill. The On/Off switch is blo-
cked when the slide switch is in centre position.
6.5 On/Off switch (Fig. 5 / Item 4)
Infi nitely variable speed control is possible with
the On/Off switch. The further you press the
switch, the higher the speed of the battery-powe-
red drill/screwdriver.
- 17 -
07.06.16 08:57 07.06.16 08:57