Inhaltsverzeichnis
Werbung
OBJ_BUCH-2402-002.book Page 13 Thursday, April 9, 2015 2:45 PM
12 SDS clamping lever for saw blade release
13 Splinter guard
14 Scale for mitre angle
15 Screw
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Jigsaw
Article number
Rated power input
Stroke rate at no load n
0
Stroke
Cutting capacity, max.
– in wood
– in aluminium
– in non-alloy steel
Bevel cuts (left/right), max.
Weight according to
EPTA-Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-11.
Typically the A-weighted noise levels of the product are:
Sound pressure level 88 dB(A); Sound power level 99 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745-2-11:
2
Sawing chipboard: a
=8.6 m/s
, K=1.5 m/s
h
2
Sawing sheet metal: a
=9.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Bosch Power Tools
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards:
EN 60745-1, EN 60745-2-11.
Technical file (2006/42/EC) at:
GST 8000 E
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
3 601 E8H 0..
Henk Becker
W
710
Executive Vice President
-1
min
800–3100
Engineering
mm
20
mm
80
mm
20
Robert Bosch GmbH, Power Tools Division
mm
10
70764 Leinfelden-Echterdingen, GERMANY
°
45
Leinfelden, 07.04.2015
Assembly
kg
2.5
/II
Before any work on the machine itself, pull the mains
Replacing/Inserting the Saw Blade
When mounting the saw blade, wear protective gloves.
Selecting a Saw Blade
An overview of recommended saw blades can be found at the
end of these instructions. Use only T-shank saw blades. The
saw blade should not be longer than required for the intended
cut.
Use a thin saw blade for narrow curve cuts.
Inserting the Saw Blade (see figure A1)
2
,
Insert the saw blade 8 (teeth in cutting direction) into the
2
, K=1.5 m/s
.
stroke rod 11 until it latches. The SDS lever 12 automatically
snaps to the rear and the saw blade is locked. Do not manually
press the lever 12 toward the rear, otherwise you could dam-
age the machine.
While inserting the saw blade, pay attention that the back of
the saw blade is positioned in the groove of the guide roller 7.
Check the tight seating of the saw blade. A loose saw
Ejecting the Saw Blade (see figure A2)
When ejecting the saw blade, hold the machine in such
Turn the SDS lever 12 toward the front in the direction of the
contact protector 9. The saw blade is released and ejected.
Splinter Guard (see figure B)
The splinter guard 13 (accessory) can prevent fraying of the
surface while sawing wood. The splinter guard can only be
used for certain saw blade types and only for cutting angles
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
plug.
Danger of injury when touching the saw blade.
blade can fall out and lead to injuries.
a manner that no persons or animals can be injured by
the ejected saw blade.
English | 13
1 619 P13 394 | (9.4.15)
Werbung
Inhaltsverzeichnis
