General Information - EINHELL TC-SS 406 E Originalbetriebsanleitung

Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
The stated noise emission values were measured
in accordance with a set of standardized criteria
and can be used to compare one power tool with
another.
The stated noise emission values can also be
used to make an initial assessment of exposure.
Warning:
The noise emission levels may vary from the level
specifi ed during actual use, depending on the
way in which the power tool is used, especially
the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Limit the operating time!
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
Anl_TC_SS_406_E_SPK13.indb 21 Anl_TC_SS_406_E_SPK13.indb 21
GB
5. Before using the tool

5.1 General information

•
All covers and safety devices must be proper-
ly fitted before the machine is switched on.
•
It must be possible for the blade to run freely.
•
When working with wood that has been previ-
ously processed, watch out for foreign bodies
such as nails or screws, etc.
•
Before you actuate the On/Off switch, make
sure that the blade is correctly fitted and that
the machine's moving parts run smoothly.
•
Check that the voltage on the rating plate is
the same as your supply voltage before you
connect the machine to the power supply.
Warning!
Always pull out the power plug before carry-
ing out any maintenance or conversion work
on the fretsaw.
5.2 Setting up the machine (Fig. 4)
For greater stability you can use the 4 mounting
holes (1) to fasten the machine to a workbench
or similar. Suitable fastening materials such as
screws etc. are available from your dealer.
5.3 Fitting the safety devices (Fig. 5)
•
Remove the hold-down device (16) from the
retaining bolt (14). To do so, use the hex key
(29) to undo the socket head screw (17).
•
Push the retaining bolt (14) into the mount on
the arm (23). Then secure it with the locking
grip (15).
•
Fit the hold-down device (16) back on the re-
taining bolt (14) by tightening the socket head
screw (17) with the hex key (29).
•
Warning! The blade guard (13) must always
be in the flipped-down position during opera-
tion.
•
Important! You can adjust the height of the
workpiece hold-down device (16) with the
locking grip (15).
•
Warning! Each time before you make a cut,
adjust the hold-down device to the thickness
of the workpiece (see Fig. 5d).
•
The hold-down device (16) must be set far
enough downwards so that it touches the
workpiece during cutting.
5.4 Fitting the blow-clean and extraction sys-
tem (Fig. 1/3)
•
Plug the articulated hose (21) onto the con-
nection on the arm (23).
- 21 -
05.06.2023 13:37:29 05.06.2023 13:37:29